Wheels on the back bottom edge, black plastic corners all around. Another coat of duratex on them both. V-plate tee nuts in and sandwiched between the sides and new strips. V-plate is duratexed and has the larger tee nuts in as bushings. Should be all ready for the block party on Saturday now.Finally...OFFICIALLY underway
-
himhimself
- Posts: 646
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Re: Finally...OFFICIALLY underway
Cut some strips of 3/8 Baltic 1.75 inches wide and glued them around the mouth, with the inside edge rostered over. Looks a little beefier now to match how they sound Wheels on the back bottom edge, black plastic corners all around. Another coat of duratex on them both. V-plate tee nuts in and sandwiched between the sides and new strips. V-plate is duratexed and has the larger tee nuts in as bushings. Should be all ready for the block party on Saturday now.
Wheels on the back bottom edge, black plastic corners all around. Another coat of duratex on them both. V-plate tee nuts in and sandwiched between the sides and new strips. V-plate is duratexed and has the larger tee nuts in as bushings. Should be all ready for the block party on Saturday now.You do not have the required permissions to view the files attached to this post.
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight)
Truck Tuba (MCM)
Next up: 2xJack12L or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight)
Truck Tuba (MCM)
Next up: 2xJack12L or family of table tubas
-
CoronaOperator
- Posts: 1648
- Joined: Wed Mar 25, 2009 7:07 pm
- Location: Medicine Hat, Alberta, Canada
Re: Finally...OFFICIALLY underway
That looks really good! 
You are going to wish you put handles on that though.
You are going to wish you put handles on that though.Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
Re: Finally...OFFICIALLY underway
+1
building BFM speakers isn't a hobby , it's an addiction
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
-
himhimself
- Posts: 646
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Re: Finally...OFFICIALLY underway
Yep, already kicking myself for not cutting the front handles in. It's on the list to be done soon.
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight)
Truck Tuba (MCM)
Next up: 2xJack12L or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight)
Truck Tuba (MCM)
Next up: 2xJack12L or family of table tubas
-
himhimself
- Posts: 646
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Re: Finally...OFFICIALLY underway
Finally took the took the time to open my t30s back up and connect all 4 speakons. Used a couple hanger bolts with wing nuts to connect the leads along with another short lead going to the driver. Now I can mix and match between between any of the cabinet inputs depending upon how and where I set them up. Should of done this ages ago. Oh well, better late than never.
You do not have the required permissions to view the files attached to this post.
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight)
Truck Tuba (MCM)
Next up: 2xJack12L or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight)
Truck Tuba (MCM)
Next up: 2xJack12L or family of table tubas