T24 #2

[Jake Jarmon]

Checking the fence for each cut - Blade



Bottom



Top



Table Saw make this go SO much faster and all my stock is the same width! I had to bust out the wire wheel and and clean the table off.



All the panels cut out ready to mark, drill, measure, cut, glue, and clamp.

[CoronaOperator]

That is exactly what my table saw looked like after it was in a flood. I used a belt sander and some aluminum oxide sanding belts and it cleaned up pretty good, then a file for the miter slots.

[David Raehn]

You could also use electrolytic reduction to remove all the rust.

Lay a wet towel on the deck and a piece of sheet steel on top of that.

Connect a car battery charger to the assembly, negative to the deck and positive to the sheet steel.

Let it run for a day. (you may have to re-wet the towel, but make sure to turn off the charger when you do that)

Any rust will be converted to elemental iron and will brush off with a nylon bristled brush.

Take a wire wheel to it if you want it to look pretty.

[Jake Jarmon]

You could also use electrolytic reduction to remove all the rust.

Lay a wet towel on the deck and a piece of sheet steel on top of that.

Connect a car battery charger to the assembly, negative to the deck and positive to the sheet steel.

Let it run for a day. (you may have to re-wet the towel, but make sure to turn off the charger when you do that)

Any rust will be converted to elemental iron and will brush off with a nylon bristled brush.

Take a wire wheel to it if you want it to look pretty.

Science

[Tom Smit]

Checking the fence for each cut - Blade

Did you add an extra 1/8" to account for the saw blade width (kerf)?

[Jake Jarmon]

Yes, I am dead reckoning to the inside edge of the blade. It has been a very busy few weeks. Got a new job, ran sound and lights at a large theater for a school musical with mariachi. PA was horribly set up and optimized although http://www.sweetwater.com/store/detail/GL2800-848 was fun to mix on. I also rebuilt my dads old Yamaha Club S115 IVs. Anyways I finished T24 #2 and here are some pics!


Marked and drilled



End of day 1



Cab 2 sealed. Forgot to take pics. Ohhhhh man just burly fit



Thinking about putting these flush mount handles here. Any thoughts?



This stuff is amazing and it's only $36 a gallon @ The Depot of Home . I tinted it slate, the darkest they had.



One down and she approves.



At this point I got side tracked and started working on the S115IVs. They were stored upside down and the floor got wet. The tops started to rot off but they have a lot of sentimental value so I couldn't bear to break em down for parts.








PAINT!!!


Two rebuilt sounding good



Two painted with one coat of textured deckover. I barely put a dent in the gallon. Time to make my ears bleed.



Somebody forgot to load the Vplate Small choir concert at my wifes school.

[CoronaOperator]

[/url]


Somebody forgot to load the Vplate Small choir concert at my wifes school.
http://s1270.photobucket.com/user/jjarm ... d.jpg.html

Please tell me you played this to 50v with the hatch down !

[J_Dunavin]

Not to 50v only 35v.
At 50v the BP102 goes poof!

[CoronaOperator]

Not to 50v only 35v.
At 50v the BP102 goes poof!

Ooops, my bad.

[Jake Jarmon]

The amp is only capable of 37-40v but the door speakers eat your face before ~ 25v. Doors speakers are running off the head unit. I successfully extended a crack in my windshield this morning on my way to work jamming some Lonely Island. Whoops...

[Tom Smit]