Introducing SPL Chart

Anything not covered elsewhere.
Post Reply
Message
Author
Mikey
Posts: 3756
Joined: Sat May 13, 2006 8:05 am
Location: Pahrump, Nevada, USA

Re: Introducing SPL Chart

#151 Post by Mikey »

Thank You, Chris!

Just one observation ... T30W27D3012LFC2 ... that didn't look right to me so I went to the SPL charts section ... that's not two cabs, it's two 3012LFs in a single 27"w T30.
"Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius, and a lot of courage, to move in the opposite direction."

Albert Einstein
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#152 Post by Chris_Allen »

Mikey wrote:Just one observation ... T30W27D3012LFC2 ... that didn't look right to me so I went to the SPL charts section ... that's not two cabs, it's two 3012LFs in a single 27"w T30.
I pondered that for a while but concluded that you couldn't get that much gain with the same mouth area. I'll get it changed.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#153 Post by Chris_Allen »







Just wanted to highlight that there are charts of the DR's that are ported and unported. All those with the compression drivers are ported. Also, the original DR200, DR250 and DR280 will be unfiltered and have the original curved horn.
Last edited by Chris_Allen on Sun Jan 07, 2018 10:26 am, edited 1 time in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#154 Post by Chris_Allen »

The new Jack 115:

Code: Select all

[spl]J115D2515,J115D2515M20,J115D2515ASD1001,J115D2515NSD2005&dbmin=80[/spl]
Last edited by Chris_Allen on Sun Jan 07, 2018 10:26 am, edited 1 time in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#155 Post by Chris_Allen »

J115 against the OmniTop15:

Code: Select all

[spl]J115D2515M20,OT15P20M&dbmin=80[/spl]
Last edited by Chris_Allen on Sun Jan 07, 2018 10:27 am, edited 1 time in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
CafSentryGnome
Posts: 258
Joined: Tue Sep 15, 2009 10:03 am
Location: South Australia

Re: Introducing SPL Chart

#156 Post by CafSentryGnome »

which chart is right? this one is different

Image
Top
User avatar
Bill Fitzmaurice
Site Admin
Posts: 28916
Joined: Tue May 02, 2006 5:59 pm

Re: Introducing SPL Chart

#157 Post by Bill Fitzmaurice »

Read the fine print on his OTop chart.
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#158 Post by Chris_Allen »

I'll verify against the latest plans, the OT15 was one of the first charts.

Yeah, as Bill says, I obsoleted it. Was replaced with this one:

Code: Select all

[spl]OT15M20,J115D2515M20&dbmin=80[/spl]


My mistake with the previous post - I've updated the first page.
Last edited by Chris_Allen on Sun Jan 07, 2018 10:29 am, edited 2 times in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#159 Post by Chris_Allen »

The new Omni 12 and Omni 15's with lower crossover frequency, different mid horn, phase plug and APT80 HF driver:

Code: Select all

[spl]O12D2512DA6AAPT80,O12DBP102X2DA6AAPT80&dbmin=80[/spl]

Code: Select all

[spl dbmin=80]O15D2515DA6AAPT80,O15DD12LFX2DA6AAPT80&dbmin=80[/spl]


Sorry for the long names!
Last edited by Chris_Allen on Sun Jan 07, 2018 10:30 am, edited 1 time in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
Mark Coward
Posts: 2601
Joined: Mon May 15, 2006 10:47 am
Location: Memphis, TN

Re: Introducing SPL Chart

#160 Post by Mark Coward »

Which LF driver was used in the DR280 for this chart?

Mark Coward
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#161 Post by Chris_Allen »

It came from the latest plans, so I would say the 2512
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
Mikey
Posts: 3756
Joined: Sat May 13, 2006 8:05 am
Location: Pahrump, Nevada, USA

Re: Introducing SPL Chart

#162 Post by Mikey »

Chris, would you please add the 24"w 3012LF T39? It's in the SPL charts section ...
http://billfitzmaurice.info/forum/viewt ... f=12&t=487

Thank You!!!
"Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius, and a lot of courage, to move in the opposite direction."

Albert Einstein
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#163 Post by Chris_Allen »

Mikey wrote:Chris, would you please add the 24"w 3012LF T39? It's in the SPL charts section ...
http://billfitzmaurice.info/forum/viewt ... f=12&t=487

Thank You!!!
Here are all the multiples on 24" wide T39's:

Code: Select all

[spl]T39W24D3012LF,T39W24D3012LFC2,T39W24D3012LFC4,T39W24D3012LFC8&dbmin=85&fmax=200[/spl]
Last edited by Chris_Allen on Sun Jan 07, 2018 10:32 am, edited 1 time in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
User avatar
Chris_Allen
Posts: 3358
Joined: Wed Jul 11, 2007 2:43 pm
Location: Huddersfield, UK

Re: Introducing SPL Chart

#164 Post by Chris_Allen »

Here are the new OmniTop 12's with the phase plug:

Code: Select all

[spl]OT12D2512M12,OT12D2512ASD1001,OT12D3012NSD2005&dbmin=80[/spl]


I need to double check the sampling range on the NSD version.
Last edited by Chris_Allen on Sun Jan 07, 2018 10:33 am, edited 1 time in total.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
Top
Mikey
Posts: 3756
Joined: Sat May 13, 2006 8:05 am
Location: Pahrump, Nevada, USA

Re: Introducing SPL Chart

#165 Post by Mikey »

Thank You, Chris!
"Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius, and a lot of courage, to move in the opposite direction."

Albert Einstein
Top
Post Reply

Return to “Everything Else”