Page 2 of 2
Re: T60 Build, problem with braces
Posted: Thu Jun 25, 2020 11:23 am
by flashero
I could make them like this, what do you think?
Re: T60 Build, problem with braces
Posted: Thu Jun 25, 2020 2:37 pm
by Grant Bunter
They are braces, use another type of glue.
Or make the braces without joints at all, from a sheet of ply.
My concern would be, if it’s not holding the braces together, it’s probably not holding the panels to the side either. So you need to find that out...
Re: T60 Build, problem with braces
Posted: Thu Jun 25, 2020 3:50 pm
by flashero
Grant Bunter wrote: ↑Thu Jun 25, 2020 2:37 pm
They are braces, use another type of glue.
Or make the braces without joints at all, from a sheet of ply.
My concern would be, if it’s not holding the braces together, it’s probably not holding the panels to the side either. So you need to find that out...
Hi, the other panels are glued ok, no problem at all, i't might be that is too little surface area so they snap easily (braces). I attach one picrue.
Re: T60 Build, problem with braces
Posted: Thu Jun 25, 2020 4:16 pm
by jimbo7
I assume you are trying to save weight. Could you cut the braces using a full piece of plywood and then plunge cut the holes out with a jigsaw? Or use a hole/cup saw and make a bunch of holes?
Re: T60 Build, problem with braces
Posted: Fri Jun 26, 2020 6:37 am
by flashero
jimbo7 wrote: ↑Thu Jun 25, 2020 4:16 pm
I assume you are trying to save weight. Could you cut the braces using a full piece of plywood and then plunge cut the holes out with a jigsaw? Or use a hole/cup saw and make a bunch of holes?
Hi, yes I could, but I have already cutted all the pieces, and to do that I'll have to buy more plywood.
I will show pictures of the finished braces soon.
Re: T60 Build, problem with braces
Posted: Thu Jul 02, 2020 1:46 pm
by flashero
Hi Bill, I have a question, with how many boxes, I will achieve the flattest response?, are the T60 tuned to 1/4 W 25Hz?
Best regards
Re: T60 Build, problem with braces
Posted: Thu Jul 02, 2020 5:13 pm
by Bill Fitzmaurice
Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.
Re: T60 Build, problem with braces
Posted: Fri Jul 03, 2020 6:00 am
by flashero
Bill Fitzmaurice wrote: ↑Thu Jul 02, 2020 5:13 pm
Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.
Thank you, I will build 6 27" Wide
Re: T60 Build, problem with braces
Posted: Mon Jul 06, 2020 8:27 pm
by Seth
Bill Fitzmaurice wrote: ↑Thu Jul 02, 2020 5:13 pm
Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.
Just for clarification... will single 12" loaded slims produce those results, or are we talking 6 cabs in the 27+" width range?
Re: T60 Build, problem with braces
Posted: Mon Jul 06, 2020 9:16 pm
by Bill Fitzmaurice
That applies to 1x15 or 2x12.
Re: T60 Build, problem with braces
Posted: Tue Jul 07, 2020 11:44 am
by flashero
Whould it be better to stack them on a horizontal line, or 3X2 stack?