Radian's T48 slim build

Post your build odyssey here.
Message
Author
User avatar
Radian
Posts: 2014
Joined: Tue Jul 29, 2008 12:56 pm
Location: Tucson, AZ

Re: Radian's T48 slim build

#46 Post by Radian »

Hope so too, Preston. :fingers: :twisted:

More progress on Cab #1 this past weekend. Dry fitting everything, drilling holes, and sinking screws.
Sect2.jpg
Sect1.jpg
Corner.jpg
Good food, good people, good times.

4 - AT
1 - TT
1 - THT Slim
2 - SLA Pro 4x6 Alphalite

User avatar
Radian
Posts: 2014
Joined: Tue Jul 29, 2008 12:56 pm
Location: Tucson, AZ

Re: Radian's T48 slim build

#47 Post by Radian »

In the slim width, the instructions are to cut panel 1 into two pieces...This had me quite worried at first as this only leaves but a sliver of panel 1 with which to attach panels 2 & 5, all the while trying to keep things absolutely square.

This is where the panel-cornering jig feature of the MFT saved my butt. Locking everything down to the table, it was no big deal to sink screws into that small piece. Once attached to a larger piece, it could be placed back up to where it needed be with much less fuss. At the end of the day it was only 1mm out of square over the entire 14" width, without the second side in place.

Sharp eyes will also notice how perilously close I came to blowing that first round of screws in the corner jig through the outer layer of panel 5, as I forgot to add an 1/8" to my combination square (my typical overhang allowance) when striking that first layout line . :shock: You can actually feel the shanks through the veneer. Too damn close. :slap:
Engine.jpg
CNRJig.jpg
Good food, good people, good times.

4 - AT
1 - TT
1 - THT Slim
2 - SLA Pro 4x6 Alphalite

User avatar
Radian
Posts: 2014
Joined: Tue Jul 29, 2008 12:56 pm
Location: Tucson, AZ

Re: Radian's T48 slim build

#48 Post by Radian »

I've got some little triangles to measure and cut that will be used to block off the space to each side of the handholds, situated behind the reflectors. While I'm not too keen on permanently enclosing those spaces for now, I definitely don't like the possibility of people or critters stuffing shit into those areas at some point in the future.
Handles1.jpg
Good food, good people, good times.

4 - AT
1 - TT
1 - THT Slim
2 - SLA Pro 4x6 Alphalite

User avatar
J_Dunavin
Posts: 1257
Joined: Sun Jul 09, 2006 3:13 pm
Location: Appleton WI
Contact:

Re: Radian's T48 slim build

#49 Post by J_Dunavin »

Turning out really nice!
2 - OTop8
2 - T39
8 - DR200
2 - DR250
9 - T24
6 - T45
1 - Auto Tuba

ACUA
Posts: 539
Joined: Sun Sep 25, 2016 6:21 pm
Location: Tucson Arizona

Re: Radian's T48 slim build

#50 Post by ACUA »

I like to hide snacks in those special hiding places, for when this roadie gets the munchies!

I could see a creepy critter making a home in there :shock:

The build is looking real good. I built my first munch of cabs by winging it and just forcing fitment in the moment, always got the edges to line up but out of square af. The last few I have done I did a little bit more test fitting with clamps and screws. I have been much more successful as I can identify issues and resolve them before it is too late, a little Adderall helps in this department. The age old tail, a little extra prep work leads to far less headaches down the road.

Radian, I always admire your aim at precision as well as your patience and detail. :clap:
Advanced Concepts Underground Audio

User avatar
Radian
Posts: 2014
Joined: Tue Jul 29, 2008 12:56 pm
Location: Tucson, AZ

Re: Radian's T48 slim build

#51 Post by Radian »

After dry fit, some more fabrication was required for the mouth braces and hand holds before finally laying down adhesive. Just like my Auto Tuba build, all the interior surfaces that wouldn't be seeing exterior treatment received a coat of polyurethane. Extra work I know, but I like the long term peace of mind. Cab #1 is all buttoned down as of yesterday. Pulled 2/3'rd of the screws today and trimmed some PL squeeze out where it was cosmetic. Finish routing, grills/mounts, access panel and speaker hardware/wiring to follow...in addition to paint.

The long visual lines play with the eyes. Gives off the illusion that the cab is just a "thin slice" perhaps, but even at the slim width (of ~15") the T48 design is still quite daunting in-person. Four of these are going to be straight-up menacing.

Pressing onwards to Cab #2. :chainsaw:
Attachments
Cab1PolyRS.jpg
Cab1dryfitsideRS.jpg
Good food, good people, good times.

4 - AT
1 - TT
1 - THT Slim
2 - SLA Pro 4x6 Alphalite

Post Reply