Did you mean to post this in the other thread?Bryan Cox wrote: ↑Fri Jan 24, 2020 8:17 pm I think for the average Joe, most won't care about the impedence a cab adds, that the tweeter arrays are not a resistive load, or even that the market is selling snake oil by using watts instead of voltage. They probably just want to build their cabs, have a beer at the end of it all, and let us "crazies" argue over the semantics.
That's why I quietly stalk the forum. I do not have the knowledge base to add to almost any conversation but I'd like to. I find most of the little nuggets of knowledge to be fascinating.
Whether it's in the plans or in the forum makes no difference to me. FEED ME SEYMOUR!!!
Found a typo
Re: Found a typo
Re: Found a typo
No I was replying in reference to the cab resistance in the previous two posts.
Otop 12 x 4 (Delta Pro 12-450a) 2x melded, 2x straight
Titan 39 x 4 (3012LF) 20" wide
Titan 39 x 4 (3012LF) 20" wide
Re: Found a typo
OOOOhhhhh. I was a little confused there for a moment. Without a quote, I had no idea what the context was. On page one, posts way back in November. I gotcha now.
Last edited by Seth on Sat Jan 25, 2020 11:42 pm, edited 1 time in total.
Re: Found a typo
Apologies all. Didn't mean to derailSethRocksYou wrote: ↑Sat Jan 25, 2020 8:42 pmOOOOhhhhh. I was a little confused there for a moment. With out a quote, I had no idea what the context was. On page one, posts way back in November. I gotcha now.
Otop 12 x 4 (Delta Pro 12-450a) 2x melded, 2x straight
Titan 39 x 4 (3012LF) 20" wide
Titan 39 x 4 (3012LF) 20" wide
Re: Found a typo
Page 5 in the panel jig plans, the Melded Tweeter Array jigs, between the photos... "...and a 2x19 inch cap on one side"
Pretty sure it's supposed to be 2x10 inch, instead of 2x19
Pretty sure it's supposed to be 2x10 inch, instead of 2x19
Re: Found a typo
On the DR300 information/sales page, below the picture it states "Take a look at this 1m/1W SPL chart, when loaded with one Eminence Definimax Twelve and two NSD2005 HF drivers:"
Yet, the chart is labeled as being a Kappalite loaded cab.
Yet, the chart is labeled as being a Kappalite loaded cab.
Re: Found a typo
T45 Instructions, page 5, Layout Diagram 3 shows aligning panel 5 90º to panel 2. And in the assembly portion it verifies that and says to screw a 90º jig to panel 2 & 5.
But, the accompanying picture on page 12 shows the jig connecting and aligning panel 5 90º to panel 3 (instead of 2).
But, the accompanying picture on page 12 shows the jig connecting and aligning panel 5 90º to panel 3 (instead of 2).
Re: Found a typo
Home page of the Tuba 60. Says, "EAW 2100" instead of EAW 2001.
Re: Found a typo
On page 21 of the Wedgehorn 6 plans, the precut size for the sides is too small. It calls for 12½" x 13" as a slightly oversized precut. But, the actual part is 12 x 13 5/8".
Guessing it is meant to read 12 x 14.
Guessing it is meant to read 12 x 14.