Dual Titan 48 Build

Post your build odyssey here.
Post Reply
Message
Author
djtrumptight
Posts: 823
Joined: Tue Dec 15, 2009 6:08 pm
Location: Detroit,Michigan

Re: Dual Titan 48 Build

#16 Post by djtrumptight »

Mark i bought some of those 5/8 brads today,im going to use them with some cleats to line up my 6/10 braces which should make that process ALOT faster,thanks for the idea.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Top
djtrumptight
Posts: 823
Joined: Tue Dec 15, 2009 6:08 pm
Location: Detroit,Michigan

Re: Dual Titan 48 Build

#17 Post by djtrumptight »

I'm sorry for not keeping this updated,its been a busy week and i had a long weekend.

Quarter round installed behind panel 11 and masking tape to maintain the bare wood surface for panel 11's installation.
Quarter round and tape (800x600).jpg
Paint behind panel 11
painting behind panel 11 (800x600).jpg
Tape removed from panel 11's glue area
Tape removed,panel 11 (850x638).jpg
Panel 11 installed
Panel 11 installed (800x600).jpg
Painted area behind panel 11
Painted area behind panel 11 (575x431).jpg
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Top
djtrumptight
Posts: 823
Joined: Tue Dec 15, 2009 6:08 pm
Location: Detroit,Michigan

Re: Dual Titan 48 Build

#18 Post by djtrumptight »

Side view before closing
Side view before closing.jpg
Side installed
Side installed.jpg
Both cabs,no braces
both cabs upright,no braces.jpg
Front braces installed
Front Braces installed.jpg
Finished T48's.I left the one access cover off,i'm letting it sit so i can check and see how the gasket compresses overnight.
finished T 48's.jpg
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Top
User avatar
Tom Smit
Posts: 7576
Joined: Sat Jan 05, 2008 1:24 pm
Location: Sarnia, Ont. Canada

Re: Dual Titan 48 Build

#19 Post by Tom Smit »

Nice job. :clap:
TomS
Top
djtrumptight
Posts: 823
Joined: Tue Dec 15, 2009 6:08 pm
Location: Detroit,Michigan

Re: Dual Titan 48 Build

#20 Post by djtrumptight »

Thanks Tom,the addiction continues
SLA Pro parts.jpg
SLA Pro Assembly.jpg
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Top
User avatar
DJPhatman
Posts: 5411
Joined: Mon Aug 14, 2006 5:08 am
Location: Warren, MI
Contact:
Contact DJPhatman

Re: Dual Titan 48 Build

#21 Post by DJPhatman »

YOU ARE A SPEAKER CABINET BUILDING ANIMAL!!! :shock: :mrgreen: :ugeek: :lol:

Now I feel stupid for not finishing the Omni Tops I drove ~450 or so miles, through a winter ice storm, to pick up. :oops: :cry: :oops: :cry: :oops:
I know money often seals the deal, but seriously, quality is an investment, not an expense... Grant Bunter
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Top
djtrumptight
Posts: 823
Joined: Tue Dec 15, 2009 6:08 pm
Location: Detroit,Michigan

Re: Dual Titan 48 Build

#22 Post by djtrumptight »

Lol,i'm have a problem,i admit it,i dont know what they call it but when i start something i hate to stop until i finish.what do u have left to do to the O Tops ?
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Top
User avatar
DJPhatman
Posts: 5411
Joined: Mon Aug 14, 2006 5:08 am
Location: Warren, MI
Contact:
Contact DJPhatman

Re: Dual Titan 48 Build

#23 Post by DJPhatman »

djtrumptight wrote:what do u have left to do to the O Tops ?
Make melded arrays, and install them. I have more pressing matters at hand currently. I am putting my house on the market, and looking to buy another home in south-west Florida. My 81 year old mother needs a warm place to stay during the winter months, so i plan to provide it for her.
I know money often seals the deal, but seriously, quality is an investment, not an expense... Grant Bunter
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Top
djtrumptight
Posts: 823
Joined: Tue Dec 15, 2009 6:08 pm
Location: Detroit,Michigan

Re: Dual Titan 48 Build

#24 Post by djtrumptight »

DJPhatman wrote:
djtrumptight wrote:what do u have left to do to the O Tops ?
Make melded arrays, and install them. I have more pressing matters at hand currently. I am putting my house on the market, and looking to buy another home in south-west Florida. My 81 year old mother needs a warm place to stay during the winter months, so i plan to provide it for her.
Thats a beautiful thing,u gotta take care of moms.Maybe i can cut them for you,i still have my melded array jig and my small table saw with the abrasive blade and a small Ryobi 2200 generator,i can come by and cut those for you in no time,let me know what you wanna do.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Top
Post Reply

Return to “Build Threads”