Hi from valve amp enthusiast from Bristol [UK]

Post Reply
Message
Author
Mr. foxen
Posts: 19
Joined: Mon Dec 16, 2013 10:54 pm

Hi from valve amp enthusiast from Bristol [UK]

#1 Post by Mr. foxen »

hmm, logged out instead of posting first try.

Happy enough with my amps that speakers is the gear territory with most room for improvement (aside from my playing, different territory) so figure this forum is place to be.

Valve amps are my area, getting them to couple up well with cabs is the real fun factor. I keep a blog mostly about the insides of them here: http://ampstack.wordpress.com/

User avatar
Oxonjohn
Posts: 49
Joined: Sat Oct 26, 2013 9:11 am
Location: Oxfordshire, UK

Re: Hi from valve amp enthusiast from Bristol [UK]

#2 Post by Oxonjohn »

Hi Mr Foxen, and welcome.

Wow, that's a lot of amps. If only I had the time, I'd love to play around with valve amps a bit more. I've recapped my VOX AC10 and recently built an Ampmaker PP-18 (cut down Baby Bluesbreaker / WEM Dominator circuit) as a backup. I've just finished an XF210 cab to go with it - not had a chance to check it out properly yet as we are out of our rehearsal room for Christmas.

I'm about 20 miles west of Oxford so not too far from you. There's also a guy in Worcester (Adam) who's built an XF212, but I don't think many more XF cabs have been built in the UK yet. I'll let you know what I think of it when I've had a chance to try it in context. Probably won't be gigging it for a couple of months at least which will give me a chance to break the drivers in.

There's loads of good advice on this forum, although not that much of it applies to the XF cabs.

John
Built: XF210
Building: None
Considering: Jack 10 Lites and Wedgehorn 6s

Grant Bunter
Posts: 6912
Joined: Mon Nov 28, 2011 11:12 am
Location: Ilfracombe Queensland Australia
Contact:

Re: Hi from valve amp enthusiast from Bristol [UK]

#3 Post by Grant Bunter »

G'day Mr Foxen,
Welcome to the forum :)
Built:
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...

User avatar
Charles Jenkinson
Posts: 1127
Joined: Sat Aug 06, 2011 3:25 pm
Location: Manchester, UK

Re: Hi from valve amp enthusiast from Bristol [UK]

#4 Post by Charles Jenkinson »

Hello Mr foxen, and welcome. :-)

Am also impressed with your amp collection. I am very much intrigued by the valve amp scene, but being a mechy, not sure where to start, or if immersion into the subject will be too time consuming, when there's other stuff to do.
2xJ12L (3012HO) switchable/melded
2xT30

Words&graphics - Audio&Acoustics - Hardware&DSP; 3 different paradigms.


User avatar
Charles Jenkinson
Posts: 1127
Joined: Sat Aug 06, 2011 3:25 pm
Location: Manchester, UK

Re: Hi from valve amp enthusiast from Bristol [UK]

#6 Post by Charles Jenkinson »

...and any experience or knowledge of electronics?
2xJ12L (3012HO) switchable/melded
2xT30

Words&graphics - Audio&Acoustics - Hardware&DSP; 3 different paradigms.

Mr. foxen
Posts: 19
Joined: Mon Dec 16, 2013 10:54 pm

Re: Hi from valve amp enthusiast from Bristol [UK]

#7 Post by Mr. foxen »

Stuff that comes from a basic education, plus after I started I got a job in a hifi factory briefly, which mean lots of soldering practice. Basic common sense and engineering instinct covered most stuff. A lot of people that don't have those kid themselves they do though.

Post Reply