yes only the edges are routed and it's made from 18mm plywood for extra strength.
the gig went great, setup was simple. i got a corner to setup my stuff , t30 corner loaded with the xti on top . table with the dj gear in front of it . to the left and right of the table speaker stands with 2 behringer tops each ( top one upside down)
bass was omnipresent with only about 15v put into the T30. did a war volume soundcheck and was immediatly told to turn it back down. didn't have time to do any EQ so it sounded a bit of ( mostly the tops ).
my uncle was the dj that evening and he said he got a lot of positive reactions about the sound although it could have been better it think. the people had a nice time and the T30 coasted allong with minimal volume setting.
it's really a great sub for this kind of gigs. goes nice and low and does it without the distortion of the mackies i used on the previous gigs.
if you're a dj and want to build some subs i can greatly recommend the T30 or it's T45 brother.
greats ketoet
t30 with kicker cvx 12 driver
Re: t30 with kicker cvx 12 driver
building BFM speakers isn't a hobby , it's an addiction
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
Re: t30 with kicker cvx 12 driver
Great gig report! I love this: "...and i was immediately told to turn it down." Freaking people, man. 
You HIRED A DJ. Did you think it would be soft, chamber music? Jeez man!
I am therefore compelled to link my favorite video, here. It's "my favorite" b/c it exemplifies my frustration with people for whom "every damn thing is too loud."
http://www.youtube.com/watch?v=W2hRApdLADA
You HIRED A DJ. Did you think it would be soft, chamber music? Jeez man!I am therefore compelled to link my favorite video, here. It's "my favorite" b/c it exemplifies my frustration with people for whom "every damn thing is too loud."
http://www.youtube.com/watch?v=W2hRApdLADA
T48 build thread: http://billfitzmaurice.info/forum/viewt ... 30&t=20315
OTop12 build thread: http://billfitzmaurice.info/forum/viewt ... 30&t=19214
OTop12 build thread: http://billfitzmaurice.info/forum/viewt ... 30&t=19214
Re: t30 with kicker cvx 12 driver
that's a great video, this weekend though i could understand why i had to turn it down. i had left the T30 channel full open when i tested the limiter in my workchop ( poor neighbours ) and it rattle everything that wasn't firmly attached in te whole building. i think they feared it would break stuff
greetz ketoet
building BFM speakers isn't a hobby , it's an addiction
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
Re: t30 with kicker cvx 12 driver
yes i had the ts parameters of the kicker cvx when i built my THT.
it was close enough to the lab 12 driver .
so it wasn't any random driver, it was checked by bill and found ok .
if the boltpattern matches it will be replaced by a lab 12 when i build it's brother.
greetz ketoet
it was close enough to the lab 12 driver .
so it wasn't any random driver, it was checked by bill and found ok .
if the boltpattern matches it will be replaced by a lab 12 when i build it's brother.
greetz ketoet
building BFM speakers isn't a hobby , it's an addiction
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah
1 x THT
1 x autotuba
2 x dr250 melded
2 x wedgehorn 10
2 x tlah