The journey begins.. 16 T60's and 12 DR280's!!

[hifibob]

Thank you and thank you Micheal! I did not know that, it will be easy enough to change it thats for sure.. So from what I understand I should stand up one of the coils?

You're welcome. This is why Bill recommends putting the crossovers on two separate boards, so you dont have to worry about this..

Arrange them like this:

Do you think if I stand up the small coil for the tweeters that will be suffice? There's a ton of hot glue holding the big one in.

Actually I just realized thats a stupid question lol

[miked]

Ah, it's NOT MDF, it's styrofoam or similar. Got it. That explains a lot. LOL! Good luck; it's looking great so far!

[hifibob]

Ah, it's NOT MDF, it's styrofoam or similar. Got it. That explains a lot. LOL! Good luck; it's looking great so far!

Hah! I guess I read that to fast, I didnt realize you were talking about medium density fiber board. Yes this is foam, its supposed to help midrange response according to Bill.

[hifibob]

For the life of me I cant find the thread that gave driver break in procedure for the 12" Kappalite NEO 3012HO.. Anybody know?

[racertomtom]

For the life of me I cant find the thread that gave driver break in procedure for the 12" Kappalite NEO 3012HO.. Anybody know?

I did mine at 30HZ, most use 10 volts.

10-12 hrs is more than adequate. Don't worry about the voltage. I just turn up the amp until the excursion is almost at xmax, Do it slowly. If you hear ticking, it's too much.

http://billfitzmaurice.info/forum/viewt ... k&start=15

[miked]

For the life of me I cant find the thread that gave driver break in procedure for the 12" Kappalite NEO 3012HO.. Anybody know?

I did mine at 30HZ, most use 10 volts.

10-12 hrs is more than adequate. Don't worry about the voltage. I just turn up the amp until the excursion is almost at xmax, Do it slowly. If you hear ticking, it's too much.

http://billfitzmaurice.info/forum/viewt ... k&start=15

Yep, +1. I use 10v @ 30Hz for 8-12 hours.

[iamlowsound]

This system is likely to seriously injure someone, I want to hear it.

lowsound

[bassmonster]

I like this build thread. I like this build thread a lot.

Excellent woodworking!

[DJ Higgumz]

Can I just fast forward and see the final product? no, I will wait like a good boy

[hifibob]

This system is likely to seriously injure someone, I want to hear it.

lowsound

Haha, sounds like you have the same problem as me. I'm a glutton for punishment

I like this build thread. I like this build thread a lot.

Excellent woodworking!

thanks bassmonster! thanks for watching its def about to get really interesting

Can I just fast forward and see the final product? no, I will wait like a good boy

I hear ya buddy I wish I was done, but stay tuned its almost there.

Today I tested 300 piezos. I also cut all 132 so tomorrow I can start assembling the melded array

[Scott Brochu]

What a pile of Piezos....Just add milk and two eggs kneed for 10 minutes put mixture threw a pasta machine and Presto!...Melded arrays.

[hifibob]

What a pile of Piezos....Just add milk and two eggs kneed for 10 minutes put mixture threw a pasta machine and Presto!...Melded arrays.

Now that would be nice! My body is beat from these.. Oddly I only had 1 bad one..

[Tom Smit]

What a pile of Piezos....Just add milk and two eggs kneed for 10 minutes put mixture threw a pasta machine and Presto!...Melded arrays.

Now that would be nice! My body is beat from these.. Oddly I only had 1 bad one..

[Grant Bunter]

Oddly I only had 1 bad one..

Just as well you had 299 spares then...

[miked]

What a pile of Piezos....Just add milk and two eggs kneed for 10 minutes put mixture threw a pasta machine and Presto!...Melded arrays.

LMAO! If only it was that easy! Testing piezos is a draining experience. Constantly hearing pink noise through this things just knocks you out.