Rane MA-6S
Rane MA-6S
I can pick up a pair of these for 200 each.... any thoughts?
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
Re: Rane MA-6S
Six channels of 100@8Ohm or 150@4Ohm. Or bridge 2 channels for 300@8Ohm. Heavy as hell. Intended usage? I have no 1st hand experience but Rane products have always been top-notch quality.
I know money often seals the deal, but seriously, quality is an investment, not an expense... Grant Bunter
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Re: Rane MA-6S
Had one for many years, ( actually the model which predates the 6S), and used it in many applications. American iron to be sure...Heavy. Can also bridge channels for 300w x3 or other combinations.. Very versatile.
I don't think rane makes the 6er any more. Excellent for perm or semi /fixed install.
I don't think rane makes the 6er any more. Excellent for perm or semi /fixed install.
Re: Rane MA-6S
yeah.... this would be for carrying =/
300 watts to subs at 8 ohms, 2 otops and a monitor would be a nice little thang though.
300 watts to subs at 8 ohms, 2 otops and a monitor would be a nice little thang though.
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
Re: Rane MA-6S
Only you can decide what you are willing to carry. Shit gets heavy and old fast at closing time. For not a lot of power, IMVHO, it's too heavy. Dependable, more than likely.sine143 wrote:yeah.... this would be for carrying =/
300 watts to subs at 8 ohms, 2 otops and a monitor would be a nice little thang though.
I know money often seals the deal, but seriously, quality is an investment, not an expense... Grant Bunter
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Re: Rane MA-6S
price was the attractive part really. power was kinda low, but I can def see its use as a monitor amp in a permanent install, or even just in a bar with multiple fills.
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
-
Kenny Kaos
- Posts: 78
- Joined: Mon Apr 02, 2007 8:45 am
- Location: PHX AZ
Re: Rane MA-6S
Got one. Three stereo amps would be pretty expensive. Use it exactly for that. permenent install for monitors. The DCX has 6 outs. Its a good match for 2 subs 2 tops and 2 mons, or a lot of combinations. I had it in a rack with my DCX. Was neat. but got old. I have a bunch of class D amps now, and use those for gigs now. But the Rane is solid and reliable.