Otop 8 future build

High power and fidelity from an easy to build cabinet.
Message
Author
kenkenni
Posts: 201
Joined: Mon Apr 30, 2012 6:34 pm
Location: Atlanta, Ga

Re: Otop 8 future build

#61 Post by kenkenni » Thu Jan 13, 2022 2:06 pm

Okay. Thanks for that Bill. I don't have the skills to interpret the graph, but I kind of figured. They are loud though and
I still can't wait to tweak everthing. Here is a short youtube video of a sound demo. Remember just a test, so no Eqing or DSP
processing as of yet. Still going to work out some kinks.

[youtube]https://www.youtube.com/watch?v=08BSJSu6XUk[/youtube]

Any bass you here is coming from an external sub which is also a diy build.

User avatar
Seth
Posts: 1906
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Otop 8 future build

#62 Post by Seth » Thu Jan 13, 2022 2:43 pm

kenkenni wrote:
Thu Jan 13, 2022 1:24 pm
Sort of like how the SLAs sound when you run them with a good sub.
The DR's, Omni Top's, and SLA's are all intended to be used with a subwoofer when full range reproduction is needed, whereas the Jack and Omni Fullrange cabs are designed to capable of being used without sub support.

From the info/sales page
The 80Hz lower usable frequency limit allows the OTop 8 to run without subs when you don't have to reproduce a lot of bass content, as in acoustic acts.
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

kenkenni
Posts: 201
Joined: Mon Apr 30, 2012 6:34 pm
Location: Atlanta, Ga

Re: Otop 8 future build

#63 Post by kenkenni » Thu Jan 13, 2022 3:20 pm

Okay I got you. Still listening to the speaker at the moment. The more I listen the more I like the sound. Maybe because
I have never used tops with compression horns. Anyone got any experience with the PA Driverack that would like to help
me with the best settings I should use?

Bruce Weldy
Posts: 7739
Joined: Fri Nov 27, 2009 11:37 am
Location: New Braunfels, TX

Re: Otop 8 future build

#64 Post by Bruce Weldy » Thu Jan 13, 2022 5:13 pm

kenkenni wrote:
Thu Jan 13, 2022 3:20 pm
Okay I got you. Still listening to the speaker at the moment. The more I listen the more I like the sound. Maybe because
I have never used tops with compression horns. Anyone got any experience with the PA Driverack that would like to help
me with the best settings I should use?
There are no best settings. Set your crossover to high pass the OT8s somewhere between 100-120hz. Set your Sub low pass about 6-10hz below where you set the OT8s. Then it's a matter of listening to them to set the balance between the sub and top. Then start EQing.

Oh, and do this outside. That will give you a good baseline. When you go into a room, then use EQ to adjust for the room.

6 - T39 4-25" 2-22" 3012LF
4 - OT12 2512 Melded/NSD2005
1 - T24
2 - XF210


"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."

Post Reply