BillFitzmaurice.info

Good plan. I made a small cabinet to hold 3D glasses do they wouldn't collect dust sheath not in use. I love how the routered plies look in a curve for an edge. That I actually did finish, oddly enough.

Thanks. I happen to like unfinished lumber, just about ask my projects are. It may get painted, but I'm in no rush. I got a new subwoofer to use!

I've moved the THT LP into my living room and I have it on end in the corner with the port facing the ceiling. It's in the rear right corner (if I'm sitting on the sofa which is against the back wall and I'm facing the TV), does it matter which way I have the port? Should Panel 8 be angled toward a ...

Thanks for the feedback. I placed the other 4 braces opposite, as Bill instructed. I made sure that if I ever had to I can replace the driver without them being in the way - I hope. http://i1098.photobucket.com/albums/g366/anikun07/THT%20LS%20Build/20150112_191459_zps1dcb3d3e.jpg Other than that, I ...

I've forgotten how to properly wire the driver because it has two pairs of posts. I believe what I had with the THT was each wire had the ends stripped and a section mid wire stripped. I passed the wire through one post so the mid-stripped section was secured and then the end of the wire was on the ...

The interior is 17" with an exterior of 18". Here's a picture of the interior of the driver chamber. http://i1098.photobucket.com/albums/g366/anikun07/THT%20LS%20Build/20150111_214418_zps2c2a654c.jpg I also took a picture with the chamber cover clamped, the cover braces easily fit into cha...

I've run into two questions. First, I followed the directions to make 8 driver chamber braces. At the dimensions specified, I can only fit 4 of them into the cab. I have to space them 2" from the edges so the driver will fit in, this doesn't let me fit anymore. Is the all right? The second ques...

draehn wrote:The chamber cover can flex too. We don't want any energy going into making the panels flex.

Thanks!

The final panels have been attached. http://i1098.photobucket.com/albums/g366/anikun07/THT%20LS%20Build/20150110_165303_zpse12bcbff.jpg http://i1098.photobucket.com/albums/g366/anikun07/THT%20LS%20Build/20150110_165233_zpsf41fa0d5.jpg I noticed I had the same problem as I did with my Auto Tuba. The ...

Yesterday I attached the baffle and braces to the cab. http://i1098.photobucket.com/albums/g366/anikun07/THT%20LS%20Build/20150109_183407_zpscbdef42e.jpg I also cut and attached panel 7 and the braces. http://i1098.photobucket.com/albums/g366/anikun07/THT%20LS%20Build/20150109_183341_zps5b20524d.jpg...

abrockey wrote:use a dab of gorilla glue and wet the surface. no screws necessary.

That's what I did. I forget such kind of glue it is, but it's the small bottle. I suspect the non-toothed nuts would need that screw though.

Is the purpose to prevent spinning when tightening the bolts? Oh! Your picture is probably with the flat base. I used the kind with the teeth. Sorry, it's not possible to tell in the picture. Thanks for the comment, if I ever use those in the future I will remember to get little screws.

Tonight was getting the baffle ready for installation. I pulled the 15" Dayton driver from my THT "Standard" last night. Today I picked up some T-Nuts for the baffle mount. The instructions were slightly different than those when I made the THT, so I basically worked from memory, look...

Thanks Rich, I wasn't sure if Baltic Birch is available at either Menards, Lowe's, or Home Depot? I thought it probably had to come from a lumber yard, which I may have a couple in my area. Peoria is about 2 1/2 hours each way, but it's good to know that it's there. Tonight I cut and glued panels 3,...

I'm in Illinois. I don't know who supplies Baltic Birch, but what's the size? Bill made it seem like it comes in 5x5 sheets. For the THT LS, three of the panels are over 60".