Jack tweeter switch diagram?
-
- Posts: 599
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Jack tweeter switch diagram?
Looking back through my Jack12 and Jacklite12 plans, and don't see anything regarding the wiring for switching a full piezo array to half and off. Considering building a pair to use for small gigs when subs with my otops are overkill, and also using as bass cabs. Could also use a fills for another room when the big system is elsewhere. Am I missing it somewhere? I'm sure I could come up with a solution, but why reinvent the wheel if it's already detailed out some where. Thanks!
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
-
- Posts: 6915
- Joined: Mon Nov 28, 2011 11:12 am
- Location: Ilfracombe Queensland Australia
- Contact:
Re: Jack tweeter switch diagram?
Built:
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
-
- Posts: 599
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Re: Jack tweeter switch diagram?
Awesome, thanks Grant!! Just what I was looking for.
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
- Clef's of Bass
- Posts: 60
- Joined: Sat Dec 26, 2020 4:21 pm
Re: Jack tweeter switch diagram?
It works well, I just used this diagram.
I used a three position slide switch instead of the toggle.
https://www.amazon.com/gp/product/B008D ... UTF8&psc=1
I didn't want the toggle lever to extend beyond the back panel.
- Strange Kevin
- Posts: 162
- Joined: Fri May 19, 2017 3:02 pm
- Location: Scottsdale AZ
Re: Jack tweeter switch diagram?
Smart!!I didn't want the toggle lever to extend beyond the back panel
I know I broke a few switches on my old J15 before I op-ed for a shallow, push button, on/off switch.
Authorized Builder - Phoenix AZ.
Main Rig - 6 DR200s - 6 T48s (30")
SLA Pros for the smaller stuff.
Main Rig - 6 DR200s - 6 T48s (30")
SLA Pros for the smaller stuff.
-
- Posts: 599
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Re: Jack tweeter switch diagram?
Thanks guys. Am thinking I will probably use a three position rocker, for that very reason so it can sit recessed. There's some center off ones marked I 0 II which would be perfect for half - off - full tweeters. I looked briefly for some that would require a little screwdriver or fingernail, like DIP switches, to really make sure they don't get accidently bumped, but no luck so far. And it's not like having it in the wrong position is going to hurt anything anyway.
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas