T-39/SLA Pro build
Forum rules
Only links to videos of our cabs are allowed. You tube only, no facebook.
Only links to videos of our cabs are allowed. You tube only, no facebook.
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
T-39/SLA Pro build
This is a short video of the fine tuning of a system i recently built for a DJ.A few days ago i posted that the SLA Pro's appeared to be running away from the subs and they were.The first thing i had wrong was the DCX 2496 set up,im running mono and should have only had a signal going to channel A,i had a signal going into channel A and B.I also changed all the filters from LR's TO BW's and last but not least,i hooked up 1 sub,then the other and the sound got lower,thats not good.Tried different cables,same effect.Opened up the jack plate on one (made sure the polarity on DCX 2496 was in normal mode),switched the negative and positive jacks on the speakons and that fixed the problem (neg. and pos. wires going to the driver are reversed) .After that,rechecked voltage limits,made minor adjustments to filters as the DJ was playing music,then some guy came into the backyard,we turned the music down to hear ,him.He said he lived on the next block and the music was too loud,he couldn't "think",i never heard a complaint like that before about music.At that point the DJ turned everything off and started wrapping up,he said that was all he needed to hear to know that he had made a wise purchase. Sorry about the wobbly video and low volume,i was using a cheap digital camera.
https://www.youtube.com/watch?v=iByeBpaaVuE
https://www.youtube.com/watch?v=iByeBpaaVuE
Last edited by djtrumptight on Mon May 18, 2015 4:24 pm, edited 1 time in total.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Re: T-39/SLA Pro build
This link works better for me.... https://www.youtube.com/watch?v=iByeBpaaVuEdjtrumptight wrote:This is a short video of the fine tuning of a system i recently built for a DJ.A few days ago i posted that the SLA Pro's appeared to be running away from the subs and they were.The first thing i had wrong was the DCX 2496 set up,im running mono and should have only had a signal going to channel A,i had a signal going into channel A and B.I also changed all the filters from LR's TO BW's and last but not least,i hooked up 1 sub,then the other and the sound got lower,thats not good.Tried different cables,same effect.Opened up the jack plate on one (made sure the polarity on DCX 2496 was in normal mode),switched the negative and positive jacks on the speakons and that fixed the problem (neg. and pos. wires going to the driver are reversed) .After that,rechecked voltage limits,made minor adjustments to filters as the DJ was playing music,then some guy came into the backyard,we turned the music down to hear ,him.He said he lived on the next block and the music was too loud,he couldn't "think",i never heard a complaint like that before about music.At that point the DJ turned everything off and started wrapping up,he said that was all he needed to hear to know that he had made a wise purchase. Sorry about the wobbly video and low volume,i was using a cheap digital camera.
https://www.youtube.com/edit?o=U&featur ... ByeBpaaVuE
TomS
-
- Posts: 1648
- Joined: Wed Mar 25, 2009 7:07 pm
- Location: Medicine Hat, Alberta, Canada
Re: T-39/SLA Pro build
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
-
- Posts: 1648
- Joined: Wed Mar 25, 2009 7:07 pm
- Location: Medicine Hat, Alberta, Canada
Re: T-39/SLA Pro build
I guess you cracked the code to the porn before I did, lolTom Smit wrote:Haha! That's too funny... one minute apart!
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
Re: T-39/SLA Pro build
Thanks fellas,i fixed it too lol.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
Re: T-39/SLA Pro build
The volt meter is reading the actual voltage going into the subs.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Re: T-39/SLA Pro build
Sounds great. Excellent work on the build, and most importantly the fix.
Good food, good people, good times.
4 - AT
1 - TT
1 - THT Slim
2 - SLA Pro 4x6 Alphalite
4 - AT
1 - TT
1 - THT Slim
2 - SLA Pro 4x6 Alphalite
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
Re: T-39/SLA Pro build
Thanks,i'm now getting a few inquiries about building for other DJ's.Radian wrote:Sounds great. Excellent work on the build, and most importantly the fix.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Re: T-39/SLA Pro build
Nice man!
Youtube will always recommend that they "smooth" the video for you because it seems shaky......DON'T DO IT.
Keep it normal.
Youtube will always recommend that they "smooth" the video for you because it seems shaky......DON'T DO IT.
Keep it normal.
Titan 39 Build
http://billfitzmaurice.info/forum/viewt ... 30&t=13717
Titan 39 Build #2
http://billfitzmaurice.info/forum/viewt ... 30&t=14458
http://billfitzmaurice.info/forum/viewt ... 30&t=13717
Titan 39 Build #2
http://billfitzmaurice.info/forum/viewt ... 30&t=14458
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
Re: T-39/SLA Pro build
thanks,i will keep that in mind.RENDOG wrote:Nice man!
Youtube will always recommend that they "smooth" the video for you because it seems shaky......DON'T DO IT.
Keep it normal.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's