Page 3 of 3
Re: Found a typo
Posted: Sat Jan 25, 2020 6:55 pm
by Seth
Bryan Cox wrote: ↑Fri Jan 24, 2020 8:17 pm
I think for the average Joe, most won't care about the impedence a cab adds, that the tweeter arrays are not a resistive load, or even that the market is selling snake oil by using watts instead of voltage. They probably just want to build their cabs, have a beer at the end of it all, and let us "crazies" argue over the semantics.
That's why I quietly stalk the forum. I do not have the knowledge base to add to almost any conversation but I'd like to. I find most of the little nuggets of knowledge to be fascinating.
Whether it's in the plans or in the forum makes no difference to me. FEED ME SEYMOUR!!!
Did you mean to post this in the other thread?
Re: Found a typo
Posted: Sat Jan 25, 2020 8:14 pm
by Bryan Cox
No I was replying in reference to the cab resistance in the previous two posts.
Re: Found a typo
Posted: Sat Jan 25, 2020 8:42 pm
by Seth
Bryan Cox wrote: ↑Sat Jan 25, 2020 8:14 pm
No I was replying in reference to the cab resistance in the previous two posts.
OOOOhhhhh. I was a little confused there for a moment. Without a quote, I had no idea what the context was. On page one, posts way back in November. I gotcha now.
Re: Found a typo
Posted: Sat Jan 25, 2020 10:09 pm
by Bryan Cox
SethRocksYou wrote: ↑Sat Jan 25, 2020 8:42 pm
Bryan Cox wrote: ↑Sat Jan 25, 2020 8:14 pm
No I was replying in reference to the cab resistance in the previous two posts.
OOOOhhhhh. I was a little confused there for a moment. With out a quote, I had no idea what the context was. On page one, posts way back in November. I gotcha now.
Apologies all. Didn't mean to derail
Re: Found a typo
Posted: Thu Feb 13, 2020 7:52 pm
by Seth
Page 5 in the panel jig plans, the Melded Tweeter Array jigs, between the photos... "...and a 2x19 inch cap on one side"
Pretty sure it's supposed to be 2x10 inch, instead of 2x19
Re: Found a typo
Posted: Wed Sep 30, 2020 10:12 am
by Seth
On the
DR300 information/sales page, below the picture it states "Take a look at this 1m/1W SPL chart, when loaded with one Eminence
Definimax Twelve and two NSD2005 HF drivers:"
Yet, the chart is labeled as being a
Kappalite loaded cab.
Re: Found a typo
Posted: Fri Oct 02, 2020 2:44 am
by Seth
T45 Instructions, page 5, Layout Diagram 3 shows aligning panel 5 90º to panel 2. And in the assembly portion it verifies that and says to screw a 90º jig to panel 2 & 5.
But, the accompanying picture on page 12 shows the jig connecting and aligning panel 5 90º to panel 3 (instead of 2).
Re: Found a typo
Posted: Sun Oct 04, 2020 7:04 am
by hotbutta
Home page of the Tuba 60. Says, "EAW 2100" instead of EAW 2001.
Re: Found a typo
Posted: Fri Oct 23, 2020 3:00 pm
by Seth
On page 21 of the Wedgehorn 6 plans, the precut size for the sides is too small. It calls for 12½" x 13" as a slightly oversized precut. But, the actual part is 12 x 13 5/8".
Guessing it is meant to read 12 x 14.