Page 11 of 21
Re: Introducing SPL Chart
Posted: Tue Nov 09, 2010 2:59 pm
by Mikey
Thank You, Chris!
Just one observation ... T30W27D3012LFC2 ... that didn't look right to me so I went to the SPL charts section ... that's not two cabs, it's two 3012LFs in a single 27"w T30.
Re: Introducing SPL Chart
Posted: Tue Nov 09, 2010 4:15 pm
by Chris_Allen
Mikey wrote:Just one observation ... T30W27D3012LFC2 ... that didn't look right to me so I went to the SPL charts section ... that's not two cabs, it's two 3012LFs in a single 27"w T30.
I pondered that for a while but concluded that you couldn't get that much gain with the same mouth area. I'll get it changed.
Re: Introducing SPL Chart
Posted: Thu Nov 25, 2010 2:50 pm
by Chris_Allen
Re: Introducing SPL Chart
Posted: Tue Nov 30, 2010 2:54 pm
by Chris_Allen
The new Jack 115:
Code: Select all
[spl]J115D2515,J115D2515M20,J115D2515ASD1001,J115D2515NSD2005&dbmin=80[/spl]
Re: Introducing SPL Chart
Posted: Tue Nov 30, 2010 2:56 pm
by Chris_Allen
J115 against the OmniTop15:
Code: Select all
[spl]J115D2515M20,OT15P20M&dbmin=80[/spl]
Re: Introducing SPL Chart
Posted: Wed Dec 01, 2010 10:27 am
by CafSentryGnome
which chart is right? this one is different
Re: Introducing SPL Chart
Posted: Wed Dec 01, 2010 12:54 pm
by Bill Fitzmaurice
Read the fine print on his OTop chart.
Re: Introducing SPL Chart
Posted: Wed Dec 01, 2010 12:57 pm
by Chris_Allen
I'll verify against the latest plans, the OT15 was one of the first charts.
Yeah, as Bill says, I obsoleted it. Was replaced with this one:
Code: Select all
[spl]OT15M20,J115D2515M20&dbmin=80[/spl]
My mistake with the previous post - I've updated the first page.
Re: Introducing SPL Chart
Posted: Sun Dec 05, 2010 3:24 pm
by Chris_Allen
The new Omni 12 and Omni 15's with lower crossover frequency, different mid horn, phase plug and APT80 HF driver:
Code: Select all
[spl]O12D2512DA6AAPT80,O12DBP102X2DA6AAPT80&dbmin=80[/spl]
Code: Select all
[spl dbmin=80]O15D2515DA6AAPT80,O15DD12LFX2DA6AAPT80&dbmin=80[/spl]
Sorry for the long names!
Re: Introducing SPL Chart
Posted: Sun Dec 12, 2010 12:02 pm
by Mark Coward
Which LF driver was used in the DR280 for this chart?
Re: Introducing SPL Chart
Posted: Mon Dec 13, 2010 6:49 am
by Chris_Allen
It came from the latest plans, so I would say the 2512
Re: Introducing SPL Chart
Posted: Sat Dec 25, 2010 9:51 am
by Mikey
Chris, would you please add the 24"w 3012LF T39? It's in the SPL charts section ...
http://billfitzmaurice.info/forum/viewt ... f=12&t=487
Thank You!!!
Re: Introducing SPL Chart
Posted: Tue Dec 28, 2010 5:59 am
by Chris_Allen
Here are all the multiples on 24" wide T39's:
Code: Select all
[spl]T39W24D3012LF,T39W24D3012LFC2,T39W24D3012LFC4,T39W24D3012LFC8&dbmin=85&fmax=200[/spl]
Re: Introducing SPL Chart
Posted: Tue Dec 28, 2010 6:03 am
by Chris_Allen
Here are the new OmniTop 12's with the phase plug:
Code: Select all
[spl]OT12D2512M12,OT12D2512ASD1001,OT12D3012NSD2005&dbmin=80[/spl]
I need to double check the sampling range on the NSD version.
Re: Introducing SPL Chart
Posted: Tue Dec 28, 2010 7:07 am
by Mikey
Thank You, Chris!