Found a typo

Anything not covered elsewhere.
Message
Author
User avatar
Seth
Posts: 2733
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Found a typo

#31 Post by Seth »

Bryan Cox wrote: Fri Jan 24, 2020 8:17 pm I think for the average Joe, most won't care about the impedence a cab adds, that the tweeter arrays are not a resistive load, or even that the market is selling snake oil by using watts instead of voltage. They probably just want to build their cabs, have a beer at the end of it all, and let us "crazies" argue over the semantics.

That's why I quietly stalk the forum. I do not have the knowledge base to add to almost any conversation but I'd like to. I find most of the little nuggets of knowledge to be fascinating.

Whether it's in the plans or in the forum makes no difference to me. FEED ME SEYMOUR!!!
Did you mean to post this in the other thread?
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

User avatar
Bryan Cox
Posts: 450
Joined: Sun Nov 22, 2015 3:01 pm
Location: Owensville, Mo

Re: Found a typo

#32 Post by Bryan Cox »

No I was replying in reference to the cab resistance in the previous two posts.
Otop 12 x 4 (Delta Pro 12-450a) 2x melded, 2x straight
Titan 39 x 4 (3012LF) 20" wide

User avatar
Seth
Posts: 2733
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Found a typo

#33 Post by Seth »

Bryan Cox wrote: Sat Jan 25, 2020 8:14 pm No I was replying in reference to the cab resistance in the previous two posts.
OOOOhhhhh. I was a little confused there for a moment. Without a quote, I had no idea what the context was. On page one, posts way back in November. I gotcha now.
Last edited by Seth on Sat Jan 25, 2020 11:42 pm, edited 1 time in total.
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

User avatar
Bryan Cox
Posts: 450
Joined: Sun Nov 22, 2015 3:01 pm
Location: Owensville, Mo

Re: Found a typo

#34 Post by Bryan Cox »

SethRocksYou wrote: Sat Jan 25, 2020 8:42 pm
Bryan Cox wrote: Sat Jan 25, 2020 8:14 pm No I was replying in reference to the cab resistance in the previous two posts.
OOOOhhhhh. I was a little confused there for a moment. With out a quote, I had no idea what the context was. On page one, posts way back in November. I gotcha now.
Apologies all. Didn't mean to derail
Otop 12 x 4 (Delta Pro 12-450a) 2x melded, 2x straight
Titan 39 x 4 (3012LF) 20" wide

User avatar
Seth
Posts: 2733
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Found a typo

#35 Post by Seth »

Page 5 in the panel jig plans, the Melded Tweeter Array jigs, between the photos... "...and a 2x19 inch cap on one side"

Pretty sure it's supposed to be 2x10 inch, instead of 2x19
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

User avatar
Seth
Posts: 2733
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Found a typo

#36 Post by Seth »

On the DR300 information/sales page, below the picture it states "Take a look at this 1m/1W SPL chart, when loaded with one Eminence Definimax Twelve and two NSD2005 HF drivers:"

Yet, the chart is labeled as being a Kappalite loaded cab.
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

User avatar
Seth
Posts: 2733
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Found a typo

#37 Post by Seth »

T45 Instructions, page 5, Layout Diagram 3 shows aligning panel 5 90º to panel 2. And in the assembly portion it verifies that and says to screw a 90º jig to panel 2 & 5.

But, the accompanying picture on page 12 shows the jig connecting and aligning panel 5 90º to panel 3 (instead of 2).
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

hotbutta
Posts: 55
Joined: Wed Dec 22, 2010 12:53 pm

Re: Found a typo

#38 Post by hotbutta »

Home page of the Tuba 60. Says, "EAW 2100" instead of EAW 2001.

User avatar
Seth
Posts: 2733
Joined: Thu Sep 10, 2009 8:06 pm
Location: Sacramento, California, USA
Contact:

Re: Found a typo

#39 Post by Seth »

On page 21 of the Wedgehorn 6 plans, the precut size for the sides is too small. It calls for 12½" x 13" as a slightly oversized precut. But, the actual part is 12 x 13 5/8".

Guessing it is meant to read 12 x 14.
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded

Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421

Post Reply