That would be a terrible Idea essientially.
response above 40ish hz would likely be similar (Plus/minus 1 db)
below 40 it would drop like a rock (about 6 to 8 db), and then exhibit a 10db peak around 18 to 20hz range.
Is there a way to quantify extension?
Re: Is there a way to quantify extension?
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
- Bill Fitzmaurice
- Site Admin
- Posts: 28646
- Joined: Tue May 02, 2006 5:59 pm
Re: Is there a way to quantify extension?
You'd get extension down to about 18Hz, but it would be rolling off until it reached 18Hz, where there would be a narrow response spike.Rich4349 wrote:how badly would it work to build a plain old hollow tube of plywood (for argument's sake say 8 feet long) that is 27x30 in cross section, and with speaker gasket, join it up to the mouth of a t60? What would the net effect be?
Re: Is there a way to quantify extension?
Would it have any (deleterious or otherwise) effects above the (previous) 25 hz cutoff?
2 DR250s, 2 27" Lab15 T-60s, 2 30" Neo Titan 39s, 1 Autotuba...and looking for more!
Re: Is there a way to quantify extension?
now if you made your 8 ft extension have about an 80 square foot mouth area
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
Re: Is there a way to quantify extension?
2 DR250s, 2 27" Lab15 T-60s, 2 30" Neo Titan 39s, 1 Autotuba...and looking for more!
Re: Is there a way to quantify extension?
not really.... I'd say each of those sides only has about 20 square feet of horn mouth.... and who knows what drivers are in there (some thing with extremely high VAS considering the size of that rear chamber)
what I'm saying is, for a single lab 15, if you were to increase the horn pathlength by 8 feet, you would need a VERY large mouth to maintain any semblance of flat response (80 square feet). Interestingly enough, this does NOT make it go any lower, but changes the design from a 1/4 wavelength box, to a 1/2 wavelength. Interestingly enough. response gets rougher as you stack more cabs at this point! lol.
Alternativly, with a mouth area of around 32 square feet, and 4 cabs, you are looking at VERY nice sensitivity (response gets rougher as you add cabs past this point though).
have fun with your mega horns
what I'm saying is, for a single lab 15, if you were to increase the horn pathlength by 8 feet, you would need a VERY large mouth to maintain any semblance of flat response (80 square feet). Interestingly enough, this does NOT make it go any lower, but changes the design from a 1/4 wavelength box, to a 1/2 wavelength. Interestingly enough. response gets rougher as you stack more cabs at this point! lol.
Alternativly, with a mouth area of around 32 square feet, and 4 cabs, you are looking at VERY nice sensitivity (response gets rougher as you add cabs past this point though).
have fun with your mega horns
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)