Hello all,
I recently scored 4 Altec Lansing VOTT A7 speakers. Assuming they work 100% & I’m looking to build a live PA for electronic music, Can I incorporate these speakers into the build or do I part out and sell to fund the new build?
Thank you!
Voice of the theatre
Re: Voice of the theatre
As far as "the build" goes, are we still talking about the system requirements you outlined in your introduction thread?
I need a multipurpose setup.
90% pre recorded DJ music. Pop - EDM - Disco - House Music.
Indoor/outdoor
Small to large crowd size with the ultimate goal to provide sound to small/medium size festivals.
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded
Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421
Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421
Re: Voice of the theatre
I recall carrying those things solo when I was 16 or so for my crappy bar band.
Over 40 years ago. I think they were old-fashioned even then.
I wouldn't consider using them in a live setup these days, though they have great retro charm.
Too bulky, and if the drivers are of the same vintage as the cabinet.. well, probably not exactly 3015LFs.
A band I play with now uses modern plastic full-range self powered dealies.
They weigh a good deal, but are compact, loud and sound OK in English pubs.
We coudn't get an A7 in the door even if we wanted to. Never mind our roadie's van.
Also, by modern standards A7s don't sound that good, and typically aren't that loud. YMMV.
Were I to furnish our kit from scratch, I'd build some of Bill's tops, subs and wedges out of spruce or poplar ply with neo drivers.
And have our neighbour (a draper) make some covers.
Light, cheap, compact and great-sounding.
Over 40 years ago. I think they were old-fashioned even then.
I wouldn't consider using them in a live setup these days, though they have great retro charm.
Too bulky, and if the drivers are of the same vintage as the cabinet.. well, probably not exactly 3015LFs.
A band I play with now uses modern plastic full-range self powered dealies.
They weigh a good deal, but are compact, loud and sound OK in English pubs.
We coudn't get an A7 in the door even if we wanted to. Never mind our roadie's van.
Also, by modern standards A7s don't sound that good, and typically aren't that loud. YMMV.
Were I to furnish our kit from scratch, I'd build some of Bill's tops, subs and wedges out of spruce or poplar ply with neo drivers.
And have our neighbour (a draper) make some covers.
Light, cheap, compact and great-sounding.
- Bill Fitzmaurice
- Site Admin
- Posts: 28646
- Joined: Tue May 02, 2006 5:59 pm
Re: Voice of the theatre
They have value to collectors, so sell them. They're totally unsuitable for electronic music.
Re: Voice of the theatre
Awesome!
Thank you, I truly appreciate the comments, I think the direction to sell and build is the best way to move forward.
Thank you, I truly appreciate the comments, I think the direction to sell and build is the best way to move forward.
-
- Posts: 8322
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: Voice of the theatre
Absolutely....
We used to play a 2000 seat dance club in Corpus Christi with just two A7s and two horns. Of course the only thing in 'em was vocals.....using an old Peavey 900 powered mixer (that had it's own legs and big rotary volume knobs). But.....that was in 1977.
Sell 'em and get something appropriate for this century.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
-
- Posts: 599
- Joined: Fri Nov 13, 2015 9:34 pm
- Location: Vancouver BC & Bloomington IN
Re: Voice of the theatre
OMG, just looked these up on ebay! Unreal what some people will pay for stuff. I remember my sister having some Altec Lansing home speakers that were beautiful with slate tops. These A7 things look like they were made by someone in their garage out of bad plywood. Yikes. Sell them and you can build something that will look better and sound amazing instead.
2xT30 (20", 3012LF)
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
2xT30 (21", 3012LF)
4xOtop J-array (Beta12, melded/straight piezos)
Truck Tuba (MCM)
Next up: 2xJack12 or family of table tubas
-
- Posts: 8322
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: Voice of the theatre
A whole lot of 'em were made in garages out of bad plywood. They were measured and copied all the time. But you'll notice that they are a horn-loaded design and were pretty damned good in their day for a speaker with a single driver.himhimself wrote: ↑Sun Sep 12, 2021 10:58 am OMG, just looked these up on ebay! Unreal what some people will pay for stuff. I remember my sister having some Altec Lansing home speakers that were beautiful with slate tops. These A7 things look like they were made by someone in their garage out of bad plywood. Yikes. Sell them and you can build something that will look better and sound amazing instead.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."