I need a new bass git cab
I need a new bass git cab
Not sure which page to put this under so I put it here.
I currently have a SWR 210 cab with an Ampeg PF500 head. The little SWR is ok but I would like something lighter. This is mainly used for rehearsal and on stage personal monitor. Suggestions ? I play 5 string.
Thanks
TomG
I currently have a SWR 210 cab with an Ampeg PF500 head. The little SWR is ok but I would like something lighter. This is mainly used for rehearsal and on stage personal monitor. Suggestions ? I play 5 string.
Thanks
TomG
DR200 x2
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
Re: I need a new bass git cab
Hadn't even thought of W10. Was thinking Jack or Omni. Will this do what my old SWR did as far as bottom etc.
DR200 x2
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
-
- Posts: 8301
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: I need a new bass git cab
In my opinion - no. An Omni or Jack would be my suggestion. A single Jack to start with some kick-back legs or an amp stand to lean it back like a monitor.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
-
- Posts: 1648
- Joined: Wed Mar 25, 2009 7:07 pm
- Location: Medicine Hat, Alberta, Canada
Re: I need a new bass git cab
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
Re: I need a new bass git cab
So a Jack 10. is the Deltalite II 2510 the premium driver, 8 ohm?
DR200 x2
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
-
- Posts: 8301
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: I need a new bass git cab
You are playing a Low B Bass......I'd go with the Jack 12 using a 3012HO.
2510 xmax - 4.2
2512 xmax - 4.9
3012 xmax - 6.2
The extra excursion is well worth it if you are going low and hitting it very hard.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
- Bill Fitzmaurice
- Site Admin
- Posts: 28619
- Joined: Tue May 02, 2006 5:59 pm
Re: I need a new bass git cab
Maximum SPL of the J12 is higher. In the intended usage for the W10, as a personal monitor, the additional output of the J12 compared to W10 wouldn't matter, so take that into consideration.Bruce Weldy wrote: ↑Tue Oct 09, 2018 1:30 pm You are playing a Low B Bass......I'd go with the Jack 12 using a 3012HO.
The extra excursion is well worth it if you are going low and hitting it very hard.
Re: I need a new bass git cab
What are approx. dimensions and weight for the 12.
DR200 x2
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
T24 16" x2
T39 20" x2
DCX2496
DEQ2496 x2
FBQ2496
Mackie DL1608
Re: I need a new bass git cab
2 - OTop8
2 - T39
8 - DR200
2 - DR250
9 - T24
6 - T45
1 - Auto Tuba
2 - T39
8 - DR200
2 - DR250
9 - T24
6 - T45
1 - Auto Tuba