The wat-cha-ma-call-it plate
The wat-cha-ma-call-it plate
I am trying to remember, but forget, the name of the plate at the back of an amp rack, with knock-outs for Speakons, powercons, etc. This is so that I can find a source. What is it called?
TomS
- Rune Bivrin
- Posts: 521
- Joined: Tue Aug 19, 2008 5:42 pm
- Location: Stockholm, Sweden
Re: The wat-cha-ma-call-it plate
In build order:
O12 with no tweeter.
3 x WedgeHorns.
2 x Jack 10 without tweeters.
2 x DR250.
2 x 16" T39
1 x Tuba 24
2 x SLA Pro (sort of...)
O12 with no tweeter.
3 x WedgeHorns.
2 x Jack 10 without tweeters.
2 x DR250.
2 x 16" T39
1 x Tuba 24
2 x SLA Pro (sort of...)
-
- Posts: 6915
- Joined: Mon Nov 28, 2011 11:12 am
- Location: Ilfracombe Queensland Australia
- Contact:
Re: The wat-cha-ma-call-it plate
Any pre punched rack panel that accepts D mounts will take XLR's, 1/4" etc, and speakons up to NL4.
Penn Elcom is one manufacturer.
So your whatsy-doover thinga-me-bob would be called a pre punched rack panel...
Penn Elcom is one manufacturer.
So your whatsy-doover thinga-me-bob would be called a pre punched rack panel...
Built:
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
-
- Posts: 676
- Joined: Tue Apr 30, 2013 5:56 pm
- Location: Colonial Beach VA
Re: The wat-cha-ma-call-it plate
BFM rig:
6 OT12
4 T48
4 WH8
Other:
56 box Electrotec LabQ rig
Way too many cables
6 OT12
4 T48
4 WH8
Other:
56 box Electrotec LabQ rig
Way too many cables
-
- Posts: 8301
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: The wat-cha-ma-call-it plate
Or build you own from a blank panel. Use a Greenlee 15/16" punch. It fits all of the xlr and speakon connectors.
https://www.amazon.com/Greenlee-730BB-1 ... ch+15%2F16
It's the only way to go if you are building custom panels. I used a step-down drill bit for several and it's a messy PITA. Finally bought the punch and felt like a fool for not doing it earlier.
https://www.amazon.com/Greenlee-730BB-1 ... ch+15%2F16
It's the only way to go if you are building custom panels. I used a step-down drill bit for several and it's a messy PITA. Finally bought the punch and felt like a fool for not doing it earlier.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
- Bill Fitzmaurice
- Site Admin
- Posts: 28620
- Joined: Tue May 02, 2006 5:59 pm
Re: The wat-cha-ma-call-it plate
A punch is what you want if you're making lots of these, but for the price of a punch you can buy three pre-punched panels.
-
- Posts: 112
- Joined: Wed Apr 04, 2012 1:30 pm
- Location: Topeka, Kansas
Re: The wat-cha-ma-call-it plate
Buy once, smile often
-
- Posts: 8301
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: The wat-cha-ma-call-it plate
+1Bill Fitzmaurice wrote: ↑Tue Jan 23, 2018 9:09 am A punch is what you want if you're making lots of these, but for the price of a punch you can buy three pre-punched panels.
The pre-punched are nice and a lot less work, but I like to do a single row on a 2U panel. More room for labeling.
Gonna start building a rack today for a local club......it will have a rack panel in it too...
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
Re: The wat-cha-ma-call-it plate
Thanks gentlemen! You gave me the info that I was looking for!
TomS