Aqua Zumba is ON!!!

Anything not covered elsewhere.
Message
Author
Bruce Weldy
Posts: 8301
Joined: Fri Nov 27, 2009 11:37 am
Location: New Braunfels, TX

Re: Aqua Zumba is ON!!!

#16 Post by Bruce Weldy »

Oscar, sent you a PM....

6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210


"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."

byacey
Posts: 948
Joined: Thu Jun 14, 2012 9:09 am
Location: Edmonton, Alberta, Canada

Re: Aqua Zumba is ON!!!

#17 Post by byacey »

Make sure everything is powered through a proper, tested ground fault interrupter, and try to avoid placing gear where anyone in wet sandals or bare feet may come in contact with it.
Built
T48s
WH8s
SX212

y2kindyz
Posts: 378
Joined: Mon Jan 05, 2009 10:54 am
Location: MISSION, TX

Re: Aqua Zumba is ON!!!

#18 Post by y2kindyz »

byacey wrote:Make sure everything is powered through a proper, tested ground fault interrupter, and try to avoid placing gear where anyone in wet sandals or bare feet may come in contact with it.
Yes sir the outlet we will be using is on a GFCI circuit and it has been tested and tripped by leaving extension cord plugged in the rain.

Thank you for the reminder I will test again just to be sure

y2kindyz
Posts: 378
Joined: Mon Jan 05, 2009 10:54 am
Location: MISSION, TX

Re: Aqua Zumba is ON!!!

#19 Post by y2kindyz »

Houston we have a casualty. Well as I am currently building some J15's for my wife's aqua Zumba she ash been using my TLAH's and other macintosh speakers. Well it's been windy in the valley and one of the TLAH's got blown over on its side. Needless to say the baffle broke. :cussing: https://flic.kr/p/UC6gvT she felt really bad and was crying when she told me. I told her no worries gives me free time in the garage when building.

I don't think it will affect performance much being at the end of the horn. But after the Jacks are done I need to make another.

User avatar
DJPhatman
Posts: 5412
Joined: Mon Aug 14, 2006 5:08 am
Location: Warren, MI
Contact:

Re: Aqua Zumba is ON!!!

#20 Post by DJPhatman »

y2kindyz wrote:Needless to say the baffle broke.
Shhhh! I hope the wifey doesn't read the forum, or over your shoulder! :twisted:

You should be able to glue that baffle crack back together and clamp it. Worse case scenario is you have to un-mount the baffle.

I see some SLA in your future! :hyper:
I know money often seals the deal, but seriously, quality is an investment, not an expense... Grant Bunter
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice

Rich4349
Posts: 855
Joined: Wed Jul 30, 2008 10:18 am
Location: Kankakee, IL

Re: Aqua Zumba is ON!!!

#21 Post by Rich4349 »

DJPhatman wrote: You should be able to glue that baffle crack back together and clamp it
+1
2 DR250s, 2 27" Lab15 T-60s, 2 30" Neo Titan 39s, 1 Autotuba...and looking for more!

CoronaOperator
Posts: 1648
Joined: Wed Mar 25, 2009 7:07 pm
Location: Medicine Hat, Alberta, Canada

Re: Aqua Zumba is ON!!!

#22 Post by CoronaOperator »

Maybe even glue a thin 1/8" or 1/4" backer board to support it.
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience

Post Reply