Bob,
Don't know if it's been discussed yet.......but, you need to make darn sure that when you wire this building that you have ample power available to run those amps. And we're not talking 15 amp circuits here. You will need several high amperage circuits to make sure there is enough power to keep from throwing circuit breakers.
That's one place not to scrimp.
Just FYI if you haven't already addressed it.
Amp selection for 8 DR280's and 10 T60's!
-
- Posts: 8317
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: Amp selection for 8 DR280's and 10 T60's!
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
Re: Amp selection for 8 DR280's and 10 T60's!
Yes sir! And stiff cabling too! Voltage sag sucksss! I probably want a 100 amp subpanel installed near the amp racks
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
Re: Amp selection for 8 DR280's and 10 T60's!
No doubt guys these amps are ridiculously hungry! Luckily I have a 600v @ 400 amp coming into the building.. I have a 200amp panel dedicated just to the DJ booth/amps rack..
My build thread.. 11 T60's and 10 DR280's http://billfitzmaurice.info/forum/viewt ... 30&t=19854
My Review! http://billfitzmaurice.info/forum/viewt ... 13&t=20567
My Review! http://billfitzmaurice.info/forum/viewt ... 13&t=20567
-
- Posts: 8317
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: Amp selection for 8 DR280's and 10 T60's!
hifibob wrote: I have a 200amp panel dedicated just to the DJ booth/amps rack..
+1
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
Re: Amp selection for 8 DR280's and 10 T60's!
make sure you get seperate 30 amp breakers for each amp! lol. you doint 4 Tubas per amp?
Built:
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)
2x Tuba 30s delta12lf loaded (gone)
4x Otop12 d2512 loaded
8x t48s (18, 18, 24, 24, 30, 30) 3015lf loaded
2x AT (1 mcm, 1 gto 804)
2x SLA Pro (dayton pa6, 6 goldwood piezo loaded)
1x bastard XF208
2x OT212 (delta pro 450a loaded, eminence psd)