Dcx 2496 question
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
Dcx 2496 question
I was wondering if I could use an output from my dcx into my amp for my tops and use a summed signal output from the dcx into the other amp input to power my sub.my reason being that I want to raise the output gain on the summed signal to get more voltage to the sub.I dont like how the system sounds using the crossover in the xls 1500.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
Re: Dcx 2496 question
That is exactly what the DCX2496 is used for.
I know money often seals the deal, but seriously, quality is an investment, not an expense... Grant Bunter
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
Accept the fact that airtight and well-braced are more important than pretty on the inside. Bill Fitzmaurice
-
- Posts: 3496
- Joined: Sat May 13, 2006 9:56 pm
Re: Dcx 2496 question
That is what it's for...and phatman is dead right..
Q, how come you're building t39 and not slim T48?
Q, how come you're building t39 and not slim T48?
BAT10, Bad Auto Tuba. Reverse folded TAT to fit JBL 1014D, 350W driver, voltage limit unknown.
Re: Dcx 2496 question
That's how I did it....input to Input A,... summed out to, I choose, Output 5, .....tops are on Output 1.
TomS
-
- Posts: 823
- Joined: Tue Dec 15, 2009 6:08 pm
- Location: Detroit,Michigan
Re: Dcx 2496 question
Ok,thanks fella's.I tried using the crossover in the XLS 1500 but i could only get about 22 volts to the T 39.Gregory i built the T 39 to use in low volume situations and small rooms,a comedy show i do once a month in particular.A T39 is short enough to fit in my 2011 Jeep Liberty replacing a EV S-181 sub i was using for the event.I built both cabs but only bought 1 driver.My next build is 2 new T-48's as well as rebuilding the 2 i already have.
Built:
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's
2 Autotuba's MCM 55 2421
8 T48's 24"wide 3015 LF
2 DR 250's melded Deltalite II 2510
2 DR 250's flat Deltalite II 2510
2 SLA HT systems
1 Table Tuba Dayton DCS 255-4
2 T 39's 20" wide 3012 LF
1 T-18 13" wide MCM 55 2421
2 SLA Pro's