Not yet (but I do have a pair of 24") These just got the second side attached. Still need to do all the finish prep, Duratex, install drivers, leak test, etc..shawn_g wrote:Very nice. Have you listened to them yet?
36" T48 x2
Re: 36" T48 x2
Re: 36" T48 x2
Bondo and sanding last night. Should be ready for a coat of paint (black latex undercoat before Duratex) by Sunday. I do have a question: I always fill all the little holes from the brad nailer, but I suspect that it may not be necessary. Thoughts?
-
- Posts: 1648
- Joined: Wed Mar 25, 2009 7:07 pm
- Location: Medicine Hat, Alberta, Canada
Re: 36" T48 x2
Depends on how many coats duratex you use. I fill them as I only use 2 coats of duratex (no primer) and the duratex will fill most but not all brad holes. Really, I would be the only one to notice them. Depends how OCD you are.Preston wrote:Bondo and sanding last night. Should be ready for a coat of paint (black latex undercoat before Duratex) by Sunday. I do have a question: I always fill all the little holes from the brad nailer, but I suspect that it may not be necessary. Thoughts?
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
Re: 36" T48 x2
Filling and sanding done, coat of flat black paint applied. Paint is still wet in photo.
- Attachments
-
- Black Boxes.jpg (20.17 KiB) Viewed 1935 times
Re: 36" T48 x2
Duratex is on. 3" Casters and protective corners installed. Hope to install the 1.5" front feet and then drivers and jack plates followed by leak testing tonight.
- Attachments
-
- casters and corners.jpg (20.85 KiB) Viewed 1905 times
Re: 36" T48 x2
Got a little done yesterday, installed the input jacks
- Attachments
-
- Input Jack.jpg (19.76 KiB) Viewed 1882 times
Re: 36" T48 x2
Front view, ready to leak test driver
- Attachments
-
- Front View Access off.jpg (16.17 KiB) Viewed 1882 times
Re: 36" T48 x2
Here they are. A pair of newly minted 36" T48 next to the vintage (original plans) 24" T48. Disclaimer: I did not build the 24's, I bought them used several years ago. I did spend the weekend retrofitting the mouth braces (they were not installed), checking driver tightness, leak testing, changing casters, front feet, and corner protectors, and applied a fresh coat of Duratex. Just ordered kits from Leyland to build one more pair of 18" wide for smaller venues when space is tight.
- Attachments
-
- Family.jpg (14.71 KiB) Viewed 1845 times
-
- Posts: 8322
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: 36" T48 x2
Very nice....
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
Re: 36" T48 x2
Looking very good. Nice build!
2 x 21" T30's with Lab12's
2 x 28" T30's with Lab12's
2 x OTop12 with Deltalite 2512
2 x 28" T30's with Lab12's
2 x OTop12 with Deltalite 2512
Re: 36" T48 x2
Good job!
Once you get the 18" cabs completed, you will have quite a bit of versatility.
Once you get the 18" cabs completed, you will have quite a bit of versatility.
TomS
Re: 36" T48 x2
Tom Smit wrote:Good job!
Once you get the 18" cabs completed, you will have to stack them all and make everyone within half a mile deaf.
4xOT12s, 2xT39s@22", TTLS@18", 2xT60@18"
Re: 36" T48 x2
Pics or it didn't happen. Freshly minted pair of 18" wide T48. 3015lf loaded.
- Attachments
-
- T48 18 inches.jpg (13.29 KiB) Viewed 1714 times
Re: 36" T48 x2
88h88 wrote:Tom Smit wrote:Good job!
Once you get the 18" cabs completed, you will have to stack them all and make everyone within half a mile deaf.
Apparently, there are going to be deaf people around you.Preston wrote:Pics or it didn't happen. Freshly minted pair of 18" wide T48. 3015lf loaded.
....my actual quote, hehe...
Good job!
Once you get the 18" cabs completed, you will have quite a bit of versatility.
TomS