how to cut the 1/2" x 1/2" x 1" nacelles for dr 250
- heavybdrums
- Posts: 366
- Joined: Fri May 22, 2015 3:46 pm
- Contact:
how to cut the 1/2" x 1/2" x 1" nacelles for dr 250
what is a good way to cut the nacelles for the dr 250's ? been scratching my head as to how to go about it, and haven't come up with a safe way to cut these small parts. Suggestions please and thanks !!
4x WH8 delta pro
2x WH10 Deltalite 2510
4x Dr250 Deltalite II 2510
8X Titan 39 3012lf, 28"
4X Tuba 60 W/ lab 15
FB: https://www.facebook.com/sunsoundservices/ likes appreciated
2x WH10 Deltalite 2510
4x Dr250 Deltalite II 2510
8X Titan 39 3012lf, 28"
4X Tuba 60 W/ lab 15
FB: https://www.facebook.com/sunsoundservices/ likes appreciated
Re: how to cut the 1/2" x 1/2" x 1" nacelles for dr 250
Cut a strip with the angle cut along one side. Then, take that strip and cut off all the little pieces (nacelles). If you can imagine stretching a nacelle from the top and bottom (as when it's installed on the cab) to make it longer, that is what I mean.
TomS
-
- Posts: 1648
- Joined: Wed Mar 25, 2009 7:07 pm
- Location: Medicine Hat, Alberta, Canada
Re: how to cut the 1/2" x 1/2" x 1" nacelles for dr 250
What Tom said with pictures:
(starts at bottom of page, continues onto next page)
http://billfitzmaurice.info/forum/viewt ... 0&start=60
(starts at bottom of page, continues onto next page)
http://billfitzmaurice.info/forum/viewt ... 0&start=60
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience
Re: how to cut the 1/2" x 1/2" x 1" nacelles for dr 250
I cut a 1/2" strip of 1/2" BB and then cut the angles with a back saw and a $5 plastic miter box from Walmart. I still have all my fingers.
- heavybdrums
- Posts: 366
- Joined: Fri May 22, 2015 3:46 pm
- Contact:
Re: how to cut the 1/2" x 1/2" x 1" nacelles for dr 250
thanks guys got them done, was easy just needed some clues.
4x WH8 delta pro
2x WH10 Deltalite 2510
4x Dr250 Deltalite II 2510
8X Titan 39 3012lf, 28"
4X Tuba 60 W/ lab 15
FB: https://www.facebook.com/sunsoundservices/ likes appreciated
2x WH10 Deltalite 2510
4x Dr250 Deltalite II 2510
8X Titan 39 3012lf, 28"
4X Tuba 60 W/ lab 15
FB: https://www.facebook.com/sunsoundservices/ likes appreciated