The SLA got more attention than the T18 today.
I started by cutting the rough whole for the array using the table saw:
I glued and built the array last night:
A quick jigsaw and the hole is made:
I jigsawed out the driver holes and tested the positions:
For the handles/ports, I first drilled a 6mm hole as a guide then using a 1 1/2" hole saw to complete:
It was back to the table saw to finish the holes:
A quick sand and they are done:
Some glue everywhere and a few misguided nails, this is what I have:
SLA Pro build thread
- Chris_Allen
- Posts: 3355
- Joined: Wed Jul 11, 2007 2:43 pm
- Location: Huddersfield, UK
Re: SLA Pro build thread
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
- Chris_Allen
- Posts: 3355
- Joined: Wed Jul 11, 2007 2:43 pm
- Location: Huddersfield, UK
Re: SLA Pro build thread
Fast forward to the textured paint phase. The areas that have had filler are showing up as a slightly darker colour. I'll have to keep an eye on that once the paint has dried.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
-
- Posts: 6915
- Joined: Mon Nov 28, 2011 11:12 am
- Location: Ilfracombe Queensland Australia
- Contact:
Re: SLA Pro build thread
More nice work
Built:
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
- Chris_Allen
- Posts: 3355
- Joined: Wed Jul 11, 2007 2:43 pm
- Location: Huddersfield, UK
Re: SLA Pro build thread
The final stages, I found some time at lunch to do some wiring. Here is the crossover glued and screwed to one of the holes for the drivers:
I'm not a fan of soldering in case i make a mistake:
I sat the crossover at the base of the cab and secured with screws:
Unfortunately the piezo array didn't fit as it was pushing against the crossover:
A quick fiddle and everything was fine:
The Alpha 6's where pressing against the foam of the brace, so I cut some holes for the air hole at the back of the driver:
The wiring was down behind the driver and we are ready for screws this evening:
I'm not a fan of soldering in case i make a mistake:
I sat the crossover at the base of the cab and secured with screws:
Unfortunately the piezo array didn't fit as it was pushing against the crossover:
A quick fiddle and everything was fine:
The Alpha 6's where pressing against the foam of the brace, so I cut some holes for the air hole at the back of the driver:
The wiring was down behind the driver and we are ready for screws this evening:
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
- Chris_Allen
- Posts: 3355
- Joined: Wed Jul 11, 2007 2:43 pm
- Location: Huddersfield, UK
Re: SLA Pro build thread
She's alive!
I need to do a bit of EQ'ing, I think it's a little 'honky' - we'll see once I get everything setup.
I need to do a bit of EQ'ing, I think it's a little 'honky' - we'll see once I get everything setup.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10