HL10C recone kit?

Helpful hints on how to build 'em, and where to get the stuff you need.
Post Reply
Message
Author
MikeLicht
Posts: 83
Joined: Tue Sep 07, 2010 10:30 am

HL10C recone kit?

#1 Post by MikeLicht » Tue Dec 31, 2019 10:37 am

I bought some HL10C drivers turns out one of them is a 10A and not a C, does anyone have or know where I can get a recone kit? I could build 2 more boxes if I can get one
Thanks,
Mike
Finished and making Music - TAT 16" with MCM 8
T39,s with HL10C sold :(
coming up Otop 12 and unknown Sub

Bruce Weldy
Posts: 6855
Joined: Fri Nov 27, 2009 11:37 am
Location: New Braunfels, TX

Re: HL10C recone kit?

#2 Post by Bruce Weldy » Tue Dec 31, 2019 11:41 am

MikeLicht wrote:
Tue Dec 31, 2019 10:37 am
I bought some HL10C drivers turns out one of them is a 10A and not a C, does anyone have or know where I can get a recone kit? I could build 2 more boxes if I can get one
Thanks,
Mike
Eminence doesn't make that kit anymore. You'll have to get really lucky to find a supplier with one in stock.....doubtful that you will.

6 - T39 4-25" 2-22" 3012LF
4 - OT12 2512 Melded/NSD2005
1 - T24
2 - XF210


"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."

User avatar
Bill Fitzmaurice
Site Admin
Posts: 27023
Joined: Tue May 02, 2006 5:59 pm

Re: HL10C recone kit?

#3 Post by Bill Fitzmaurice » Tue Dec 31, 2019 12:28 pm

I may have some, it'll be a bit before I can make my way through the snow to my workshop to check it out.

Bruce Weldy
Posts: 6855
Joined: Fri Nov 27, 2009 11:37 am
Location: New Braunfels, TX

Re: HL10C recone kit?

#4 Post by Bruce Weldy » Tue Dec 31, 2019 12:36 pm

Bill Fitzmaurice wrote:
Tue Dec 31, 2019 12:28 pm
I may have some, it'll be a bit before I can make my way through the snow to my workshop to check it out.
Yeah, it's cold here too......had to keep my window up most of the time while I was driving this morning....in my short-sleeved shirt. :mrgreen:

6 - T39 4-25" 2-22" 3012LF
4 - OT12 2512 Melded/NSD2005
1 - T24
2 - XF210


"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."

User avatar
Bill Fitzmaurice
Site Admin
Posts: 27023
Joined: Tue May 02, 2006 5:59 pm

Re: HL10C recone kit?

#5 Post by Bill Fitzmaurice » Tue Dec 31, 2019 3:39 pm

I just got back from Vegas, where the temps were in the 50s during the day, 40s at night. I wore a short sleeve golf shirt and unlined windbreaker. I saw more than a few pussies wearing big down coats ala George Costanza. I can't imagine what they'd do in cold weather.

Bruce Weldy
Posts: 6855
Joined: Fri Nov 27, 2009 11:37 am
Location: New Braunfels, TX

Re: HL10C recone kit?

#6 Post by Bruce Weldy » Tue Dec 31, 2019 5:03 pm

I think it's sometimes more about fashion than comfort.

6 - T39 4-25" 2-22" 3012LF
4 - OT12 2512 Melded/NSD2005
1 - T24
2 - XF210


"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."

User avatar
Bill Fitzmaurice
Site Admin
Posts: 27023
Joined: Tue May 02, 2006 5:59 pm

Re: HL10C recone kit?

#7 Post by Bill Fitzmaurice » Tue Dec 31, 2019 5:47 pm

I see that from numbskull teenage boys who wear shorts in the dead of winter, which around here can mean a few weeks never reaching above freezing. No, these were middle aged average Jills and Joes who must have been visiting from Panama.

User avatar
Bill Fitzmaurice
Site Admin
Posts: 27023
Joined: Tue May 02, 2006 5:59 pm

Re: HL10C recone kit?

#8 Post by Bill Fitzmaurice » Wed Jan 01, 2020 11:46 am

I managed to get to my shop and found that I do have some HL10 kits, but they're 8 ohm HL10A. not 4 ohm HL10C.

MikeLicht
Posts: 83
Joined: Tue Sep 07, 2010 10:30 am

Re: HL10C recone kit?

#9 Post by MikeLicht » Thu Jan 02, 2020 10:37 am

Bill, thank you for checking. I could make MY "C" an "A" I suppose to have a pair, but not sure what I would put them in.
Finished and making Music - TAT 16" with MCM 8
T39,s with HL10C sold :(
coming up Otop 12 and unknown Sub

Post Reply