T60 Build, problem with braces (solved)
-
- Posts: 6915
- Joined: Mon Nov 28, 2011 11:12 am
- Location: Ilfracombe Queensland Australia
- Contact:
Re: T60 Build, problem with braces
They are braces, use another type of glue.
Or make the braces without joints at all, from a sheet of ply.
My concern would be, if it’s not holding the braces together, it’s probably not holding the panels to the side either. So you need to find that out...
Or make the braces without joints at all, from a sheet of ply.
My concern would be, if it’s not holding the braces together, it’s probably not holding the panels to the side either. So you need to find that out...
Built:
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
DR 250: x 2 melded array, 2x CD horn, March 2012 plans.
T39's: 4 x 20" KL3010LF , 2 x 28" 3012LF.
WH8: x 6 with melded array wired series/parallel.
Bunter's Audio and Lighting "like"s would be most appreciated...
Re: T60 Build, problem with braces
Hi, the other panels are glued ok, no problem at all, i't might be that is too little surface area so they snap easily (braces). I attach one picrue.Grant Bunter wrote: ↑Thu Jun 25, 2020 2:37 pm They are braces, use another type of glue.
Or make the braces without joints at all, from a sheet of ply.
My concern would be, if it’s not holding the braces together, it’s probably not holding the panels to the side either. So you need to find that out...
Re: T60 Build, problem with braces
I assume you are trying to save weight. Could you cut the braces using a full piece of plywood and then plunge cut the holes out with a jigsaw? Or use a hole/cup saw and make a bunch of holes?
BFM builds:
XF212
T24 BP102 24"
2x SLA's 6-5" mids, 9- gt-302's
2x AT 14" MCM 55-2421
TrT 5" MCM 55-2421
AT 18" JBL GTO804
2x OT12 flat array
2x SLA Pro 2-Alpha 6's 2-Goldwoods
2x T39 24" 3012lf
Simplex 10 BP102
XF212
T24 BP102 24"
2x SLA's 6-5" mids, 9- gt-302's
2x AT 14" MCM 55-2421
TrT 5" MCM 55-2421
AT 18" JBL GTO804
2x OT12 flat array
2x SLA Pro 2-Alpha 6's 2-Goldwoods
2x T39 24" 3012lf
Simplex 10 BP102
Re: T60 Build, problem with braces
Hi, yes I could, but I have already cutted all the pieces, and to do that I'll have to buy more plywood.
I will show pictures of the finished braces soon.
Re: T60 Build, problem with braces
Hi Bill, I have a question, with how many boxes, I will achieve the flattest response?, are the T60 tuned to 1/4 W 25Hz?
Best regards
Best regards
- Bill Fitzmaurice
- Site Admin
- Posts: 28647
- Joined: Tue May 02, 2006 5:59 pm
Re: T60 Build, problem with braces
Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.
Re: T60 Build, problem with braces
Thank you, I will build 6 27" WideBill Fitzmaurice wrote: ↑Thu Jul 02, 2020 5:13 pm Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.
Re: T60 Build, problem with braces
Just for clarification... will single 12" loaded slims produce those results, or are we talking 6 cabs in the 27+" width range?Bill Fitzmaurice wrote: ↑Thu Jul 02, 2020 5:13 pm Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.
Build in process - 2 WH6, one Alpha 6a loaded, one PRV Audio 6MB250-NDY loaded
Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421
Two 2x6 shorty SLA Pro's
One T39, 16", 3012LF loaded
Tall AutoTuba, 20" wide, 2x 8" MCM 55-2421
TruckTuba, 8½" wide, 2x 8" MCM 55-2421
- Bill Fitzmaurice
- Site Admin
- Posts: 28647
- Joined: Tue May 02, 2006 5:59 pm
Re: T60 Build, problem with braces
That applies to 1x15 or 2x12.
Re: T60 Build, problem with braces
Whould it be better to stack them on a horizontal line, or 3X2 stack?