BillFitzmaurice.info

In the PDF it is page 25 -to first half of page 28 With 12 Delta Lite and 2x ASD. I would like configuration where I can switch the ASD off, only turn on one or both on as needed. Where would the 3 phase switch would be located in the circuit? Then what by-pass and cross over and other el. parts do ...

Jack 12 with Delta lite II 2512 and 2x ASD1001B https://www.amazon.com/Eminence-ASD1001B-Frequency-Titanium-Driver/dp/B00HYDI7ZG/?_encoding=UTF8&pd_rd_w=XgeMW&pf_rd_p=bbb6bbd8-d236-47cb-b42f-734cb0cacc1f&pf_rd_r=K6YMTP56SAT70KYGEGTB&pd_rd_r=92e3c378-e76f-4d73-aa0d-e789e980e65d&pd...

So finally I stop beating around the bush I got me Jack12(2512,piezzo array,500w cross over l/h,speakons). No time to build one but I swear I will one of these days do so. So I purchased one, its on it way. Thanx to forum here & Trey Fisher. I plane in future to add another jack12 ,and monitors....

All I need is mathematical formula that are written mathematically correct withe explanation of values used.

Thanx.

That was eazy. If you have multiple drivers in ones speaker then I just add all the RMS values together to calculate total amps needed? If the speakers are in paralel the ohms will lower and RMS will get higher.(and the formula for this was ?) If they are in serial the ohms will get higher and the R...

so RMS IS the amplifier requirement!
No program,no peak is the RMS that my amp have to have.
Ok got it.

And yes going in circles seems to be my talent

i wont to understand it.i will look the speaker specs i get the RMS from there and ohms from there. and the formula to get total volts and to get total amps is?(if someone can answer this in dummy version I appreciate it) and then i get the totals of that and multiply them together to get watts need...

I do not want to be total ignor but could you use the 2510 specs so i see how you use it? prefer using the math formula instead of a online tool. OOPS....I was wrong, that didn't do the trick. "Gee mister, thanks for the free meal and the wine was great. The desert was wonderful. Since you are...

that is what i wont just braked down to understand it and by being here that is my part of research.

if the RMS of delta is 250 and the ohm is 8 the total i get is 44.7 V and 5.6 amp. how this is goin to tel me the wattage required of the amp? beside the quess of multiplying V X amps= watts? 44.7 x5.6 =250watts? so the amp have to be least 250W no need fot overhead no nedd to reserve no need to?hel...

I do not want to be total ignor but could you use the 2510 specs so i see how you use it?
prefer using the math formula instead of a online tool.

"volts from amp = square root(watts * ohms)" is this square root x (watts x ohms)=volts needed for amp? Here's the easy way. Use this calculator. http://www.sengpielaudio.com/calculator-ohm.htm Remember that the max voltage is in the plans for the subs. Some speakers can take the full vol...

"volts from amp = square root(watts * ohms)"
is this square root x (watts x ohms)=volts needed for amp?

definitely would like to know how chose my own amp yes.

I get from speaker the RMS value?
Or should i use the program or the peak?

Then add all driver values together and all the tweets and other el. components= wattage= get amp with that wattage?

the reason I'm asking the question is to get well scaled answers.Do not have need to under power anything if I get recommendations.

So if you can drop some model numbers and names of recommended equipment for each scenario that would be good.
I will check in the recommended Behringer. Any other?