BillFitzmaurice.info

Grant Bunter wrote: ↑Thu Aug 27, 2020 3:54 pm Nice!
What will you be using to as a limiter?

Thank you!. Now I have an Ashly Protea 4.8, but I was going to use a plate amplifier with dsp. With shipping overseas expensive, perhaps I will buy a 4 CH class d amp with dsp (Powersoft Clone), soon I have to decide.

SethRocksYou wrote: ↑Thu Aug 27, 2020 9:04 am Here's some music to let those beasts do some justice to...

https://www.youtube.com/c/Siryn/videos
https://www.youtube.com/channel/UCkt2uC ... pCQ/videos

Thanks, I will try them soon

Dale Hammer wrote: ↑Thu Aug 27, 2020 7:55 am Looks great! Nice work.

Thank you Dale!, can't wait to fire them up and shake some bodies

Hi!, how are you people. I have finished the build, the only remaing tasks is to load the cabinets, put the speakon connectors, some cab corners, and perhaps add a grill. When its all done, I will post some measurements, I will compare with the old BR cabs i'd made for the LAB15 (med size vented clu...

Here some pics, almost done

Set 'em both to the correct voltage.....BUT, also put a volt meter on the outputs and check them before ever connecting a speaker. If you don't know how to do this, we can tell you how. So, RMS and Peak both to 50V (Lab12) and 60V (Lab15). Yes, I know how to meausure voltage, I will feed them with ...

Hi to all, soon the T60's will be finished :). I have a question about setting the limiters, for the LAB12 and LAB15 drivers, in the plans it says, that the voltage limit for the 12 is 50V and 15 60V. I will have a class d amplifier driving each box separately, the amp is rated 1000w 8Ohm peak, it h...

Bill Fitzmaurice wrote: ↑Mon Jul 06, 2020 9:16 pm That applies to 1x15 or 2x12.

Whould it be better to stack them on a horizontal line, or 3X2 stack?

Bill Fitzmaurice wrote: ↑Thu Jul 02, 2020 5:13 pm Outdoors it takes six to go flat to 26Hz. Indoors it takes as few as two.

Thank you, I will build 6 27" Wide

Hi Bill, I have a question, with how many boxes, I will achieve the flattest response?, are the T60 tuned to 1/4 W 25Hz?

Best regards

I assume you are trying to save weight. Could you cut the braces using a full piece of plywood and then plunge cut the holes out with a jigsaw? Or use a hole/cup saw and make a bunch of holes? Hi, yes I could, but I have already cutted all the pieces, and to do that I'll have to buy more plywood. I...

They are braces, use another type of glue. Or make the braces without joints at all, from a sheet of ply. My concern would be, if it’s not holding the braces together, it’s probably not holding the panels to the side either. So you need to find that out... Hi, the other panels are glued ok, no prob...

I could make them like this, what do you think?

Rich4349 wrote: ↑Thu Jun 25, 2020 9:49 am A very basic lap joint would look better than that, and even have a little more contact area.

https://kitchencabinetkings.com/glossary/lap-joint/

Thank you, yes, the problem is there is more than 400 parts to mill, for the braces xD

Here's what Gorilla Glue (popular option here in the States) looks like after curing. Gorilla Glue is an expanding polyurethane adhesive, however it is not recommended as a construction adhesive for any Bill Fitzmaurice designs that require airtight construction. https://billfitzmaurice.info/forum/...