36" T48 x2

Post your build odyssey here.
Message
Author
Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#16 Post by Preston »

shawn_g wrote:Very nice. Have you listened to them yet?
Not yet (but I do have a pair of 24") These just got the second side attached. Still need to do all the finish prep, Duratex, install drivers, leak test, etc..

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#17 Post by Preston »

Bondo and sanding last night. Should be ready for a coat of paint (black latex undercoat before Duratex) by Sunday. I do have a question: I always fill all the little holes from the brad nailer, but I suspect that it may not be necessary. Thoughts?

CoronaOperator
Posts: 1648
Joined: Wed Mar 25, 2009 7:07 pm
Location: Medicine Hat, Alberta, Canada

Re: 36" T48 x2

#18 Post by CoronaOperator »

Preston wrote:Bondo and sanding last night. Should be ready for a coat of paint (black latex undercoat before Duratex) by Sunday. I do have a question: I always fill all the little holes from the brad nailer, but I suspect that it may not be necessary. Thoughts?
Depends on how many coats duratex you use. I fill them as I only use 2 coats of duratex (no primer) and the duratex will fill most but not all brad holes. Really, I would be the only one to notice them. Depends how OCD you are.
Built:
17" width 10" driver Autotuba
2 x 29" width dual Lab12 Tuba60
6 x DR250 2510/asd1001
In progress:
2 x DR250 2510/asd1001
For best results, point the loud end of the array towards the audience

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#19 Post by Preston »

Filling and sanding done, coat of flat black paint applied. Paint is still wet in photo.
Attachments
Black Boxes.jpg
Black Boxes.jpg (20.17 KiB) Viewed 1916 times

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#20 Post by Preston »

Duratex is on. 3" Casters and protective corners installed. Hope to install the 1.5" front feet and then drivers and jack plates followed by leak testing tonight.
Attachments
casters and corners.jpg
casters and corners.jpg (20.85 KiB) Viewed 1886 times

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#21 Post by Preston »

Got a little done yesterday, installed the input jacks
Attachments
Input Jack.jpg
Input Jack.jpg (19.76 KiB) Viewed 1863 times

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#22 Post by Preston »

Mounted the drivers
Attachments
Driver Mounted.jpg
Driver Mounted.jpg (18.86 KiB) Viewed 1863 times

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#23 Post by Preston »

Front view, ready to leak test driver
Attachments
Front View Access off.jpg
Front View Access off.jpg (16.17 KiB) Viewed 1863 times

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#24 Post by Preston »

Here they are. A pair of newly minted 36" T48 next to the vintage (original plans) 24" T48. Disclaimer: I did not build the 24's, I bought them used several years ago. I did spend the weekend retrofitting the mouth braces (they were not installed), checking driver tightness, leak testing, changing casters, front feet, and corner protectors, and applied a fresh coat of Duratex. Just ordered kits from Leyland to build one more pair of 18" wide for smaller venues when space is tight.
Attachments
Family.jpg
Family.jpg (14.71 KiB) Viewed 1826 times

Bruce Weldy
Posts: 8301
Joined: Fri Nov 27, 2009 11:37 am
Location: New Braunfels, TX

Re: 36" T48 x2

#25 Post by Bruce Weldy »

Very nice....

6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210


"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."

chrisj360
Posts: 114
Joined: Fri Sep 20, 2013 1:37 pm
Location: Bellingham, WA

Re: 36" T48 x2

#26 Post by chrisj360 »

Looking very good. Nice build!
2 x 21" T30's with Lab12's
2 x 28" T30's with Lab12's
2 x OTop12 with Deltalite 2512

User avatar
Tom Smit
Posts: 7457
Joined: Sat Jan 05, 2008 1:24 pm
Location: Sarnia, Ont. Canada

Re: 36" T48 x2

#27 Post by Tom Smit »

Good job!
Once you get the 18" cabs completed, you will have quite a bit of versatility.
TomS

88h88
Posts: 1603
Joined: Mon Jul 04, 2011 10:20 am
Location: Coventry, UK

Re: 36" T48 x2

#28 Post by 88h88 »

Tom Smit wrote:Good job!
Once you get the 18" cabs completed, you will have to stack them all and make everyone within half a mile deaf.
:D
4xOT12s, 2xT39s@22", TTLS@18", 2xT60@18"

Preston
Posts: 194
Joined: Mon Apr 14, 2008 3:59 pm
Location: Springfield, IL

Re: 36" T48 x2

#29 Post by Preston »

Pics or it didn't happen. Freshly minted pair of 18" wide T48. 3015lf loaded.
Attachments
T48 18 inches.jpg
T48 18 inches.jpg (13.29 KiB) Viewed 1695 times

User avatar
Tom Smit
Posts: 7457
Joined: Sat Jan 05, 2008 1:24 pm
Location: Sarnia, Ont. Canada

Re: 36" T48 x2

#30 Post by Tom Smit »

88h88 wrote:
Tom Smit wrote:Good job!
Once you get the 18" cabs completed, you will have to stack them all and make everyone within half a mile deaf.
:D
Preston wrote:Pics or it didn't happen. Freshly minted pair of 18" wide T48. 3015lf loaded.
Apparently, there are going to be deaf people around you. :lol:



:clap: ....my actual quote, hehe...
Good job!
Once you get the 18" cabs completed, you will have quite a bit of versatility.
TomS

Post Reply