Something very satisfying about cutting flat packs on a table saw.
The way the chisel goes through warm PL mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm
2x OT12
- Jake Jarmon
- Posts: 43
- Joined: Wed Oct 29, 2014 2:48 pm
- Location: Buda, TX
- Contact:
2x OT12
2 - T24 24" BP102 "Twinning"
2 - OT112 Delta Pro 12 Melded Array **In Progress**
2 - OT112 Delta Pro 12 Melded Array **In Progress**
- Chris_Allen
- Posts: 3355
- Joined: Wed Jul 11, 2007 2:43 pm
- Location: Huddersfield, UK
Re: 2x OT12
Looks like 1/2" stacked together, 2 pieces for each cut.Tom Smit wrote:Good progress.
Is that 3/4" plywood?
On the edges of your cuts, it looks like you have a bit of gripping from either your fence or table top - might be time for a quick light sand and a bit of wax.
Built:
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
6xDR200, 2xT39, 2xT48, 2xJack110, 1xOmni10.5, 1xAutotuba, 1xT18, 1xSLA Pro, 1xW8, 1xW10
- Jake Jarmon
- Posts: 43
- Joined: Wed Oct 29, 2014 2:48 pm
- Location: Buda, TX
- Contact:
Re: 2x OT12
Chris_Allen wrote:Looks like 1/2" stacked together, 2 pieces for each cut.Tom Smit wrote:Good progress.
Is that 3/4" plywood?
On the edges of your cuts, it looks like you have a bit of gripping from either your fence or table top - might be time for a quick light sand and a bit of wax.
Yes cutting 2 baffles at once. You are right I cleaned the table and fence a few weeks ago but it definitely needs some more TLC.
2 - T24 24" BP102 "Twinning"
2 - OT112 Delta Pro 12 Melded Array **In Progress**
2 - OT112 Delta Pro 12 Melded Array **In Progress**
- Jake Jarmon
- Posts: 43
- Joined: Wed Oct 29, 2014 2:48 pm
- Location: Buda, TX
- Contact:
Re: 2x OT12
Can I rotate the woofer spacer 22.5 degrees so the points are 0,90,180,360 when I install it without adverse effects? It looks cooler that way and is much easier to align.
2 - T24 24" BP102 "Twinning"
2 - OT112 Delta Pro 12 Melded Array **In Progress**
2 - OT112 Delta Pro 12 Melded Array **In Progress**
-
- Posts: 8322
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: 2x OT12
Jake Jarmon wrote:Can I rotate the woofer spacer 22.5 degrees so the points are 0,90,180,360 when I install it without adverse effects? It looks cooler that way and is much easier to align.
Yep....it only serves to give more holding power to the screws.....
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."