OmniTop 12 (x4) and Titan 39 (x2) build
OmniTop 12 (x4) and Titan 39 (x2) build
My Dad and I started a new build this weekend for our church. See this thread for details: http://billfitzmaurice.info/forum/viewt ... 28&t=17150
Here's what we'll end up with when we're done:
(4) OmniTop 12 - 3012HO loaded - melded arrays
(2) Titan 39 - Lab 12 loaded - 28" wide
I ordered the "Deluxe" kits from Leland (http://speakerhardware.com) for both the OmniTop and Titan and received everything on Thursday. I cheated and had Leland make the melded arrays , which look great by the way! When Leland says that the kits include everything except what's mentioned on the product page, he's not kidding. He even threw in a set of BF and Speakerhardware badges. Here's part of my order:
Starting with the OmniTops, we decided to pre-cut all of the panels first. I know that everyone says to build as you go, but I think we'll be fine. However, we'll probably build the Titans as we go since the angles and braces get tricky.
Some of our cut parts:
Baffle pics:
Forgot to take any assembly pictures up to this point:
Sides on:
Mounting flange installed:
That's all we got done this weekend, but I'm sure we'll be working on it more during the week.
I still need to order some metal grills for the front. I was thinking about ordering from the speakerparts! guy on ebay or "Reliable Hardware". Any other suggestions? The stuff at Lowes and Menards is a little too "industrial" for my liking.
Here's what we'll end up with when we're done:
(4) OmniTop 12 - 3012HO loaded - melded arrays
(2) Titan 39 - Lab 12 loaded - 28" wide
I ordered the "Deluxe" kits from Leland (http://speakerhardware.com) for both the OmniTop and Titan and received everything on Thursday. I cheated and had Leland make the melded arrays , which look great by the way! When Leland says that the kits include everything except what's mentioned on the product page, he's not kidding. He even threw in a set of BF and Speakerhardware badges. Here's part of my order:
Starting with the OmniTops, we decided to pre-cut all of the panels first. I know that everyone says to build as you go, but I think we'll be fine. However, we'll probably build the Titans as we go since the angles and braces get tricky.
Some of our cut parts:
Baffle pics:
Forgot to take any assembly pictures up to this point:
Sides on:
Mounting flange installed:
That's all we got done this weekend, but I'm sure we'll be working on it more during the week.
I still need to order some metal grills for the front. I was thinking about ordering from the speakerparts! guy on ebay or "Reliable Hardware". Any other suggestions? The stuff at Lowes and Menards is a little too "industrial" for my liking.
-
- Posts: 1384
- Joined: Wed Jul 13, 2011 9:23 am
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Nice build. Looking forward to following it!
Re: OmniTop 12 (x4) and Titan 39 (x2) build
very nice clean build; are you going to coated it with something?
- LelandCrooks
- Posts: 7244
- Joined: Thu May 04, 2006 9:36 am
- Location: Midwest/Kansas/Speaker Nirvana
- Contact:
Re: OmniTop 12 (x4) and Titan 39 (x2) build
You can rough precut the titans. Otops are a pretty easy precut.
Have fun!
Have fun!
If it's too loud, you're even older than me! Like me.
http://www.speakerhardware.com
http://www.speakerhardware.com
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Thanks everyone. We had a few hours to work tonight and got a little more done on OTop #1. I'll post some pictures tomorrow.
Boostfab: I've got two gallons of duratex to paint all of the cabs with. Hoping it's enough for everything.
Boostfab: I've got two gallons of duratex to paint all of the cabs with. Hoping it's enough for everything.
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Pictures as promised:
We put a few screws in the piezo array to see how it's going to look.
Jack plate installed.
Oooh....aaahhh.
We put a few screws in the piezo array to see how it's going to look.
Jack plate installed.
Oooh....aaahhh.
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Look sooooo much cleaner than my OT12s...
4xOT12s, 2xT39s@22", TTLS@18", 2xT60@18"
-
- Posts: 8317
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: OmniTop 12 (x4) and Titan 39 (x2) build
What are you going to do with the extra gallon?shawn_g wrote:Thanks everyone. We had a few hours to work tonight and got a little more done on OTop #1. I'll post some pictures tomorrow.
Boostfab: I've got two gallons of duratex to paint all of the cabs with. Hoping it's enough for everything.
That stuff does a long way.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
Re: OmniTop 12 (x4) and Titan 39 (x2) build
That's good to know. I was estimating when I ordered and didn't want to come up short. I may end up building some wedgehorns in the future, so I'm sure it will get used up eventually.Bruce Weldy wrote: What are you going to do with the extra gallon?
That stuff does a long way.
Mine has plenty of imperfections, the small pictures hide them well.88h88 wrote:Look sooooo much cleaner than my OT12s...
-
- Posts: 8317
- Joined: Fri Nov 27, 2009 11:37 am
- Location: New Braunfels, TX
Re: OmniTop 12 (x4) and Titan 39 (x2) build
2 T39s, 4 OT12s, 3 WH10s, light box, and mixer case. So far 1 full gallon and about an inch and a half out of the second one.shawn_g wrote:I'm sure it will get used up eventually.
6 - T39 3012LF
4 - OT12 2512
1 - T24
1 - SLA Pro
2 - XF210
"A system with a few knobs set up by someone who knows what they are doing is always better than one with a lot of knobs set up by someone who doesn't."
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Can someone comment on whether this mattress topper will be adequate for the dampening?
It's the only style they had at Walmart and I haven't opened the package yet in case I need to return it.
It's about 1.25" at the highest point and only .5" at the lowest. The plans say between 1" and 2", but I'm not sure if that means a mimimum of 1" for the low part or a minimum of 1" for the high part.
It's the only style they had at Walmart and I haven't opened the package yet in case I need to return it.
It's about 1.25" at the highest point and only .5" at the lowest. The plans say between 1" and 2", but I'm not sure if that means a mimimum of 1" for the low part or a minimum of 1" for the high part.
- Jon Barnhardt
- Posts: 718
- Joined: Wed Jun 08, 2011 1:20 pm
- Location: Bismarck, ND - Licensed builder
- Contact:
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Looks like the same stuff I've used before.
Re: OmniTop 12 (x4) and Titan 39 (x2) build
Sounds good. Thanks.Jon Barnhardt wrote:Looks like the same stuff I've used before.
Re: OmniTop 12 (x4) and Titan 39 (x2) build
if you use the spray adhesive, spray on both surfaces..the wood and the foam, and let it sit for a bit before applying the foam onto the wood.
Re: OmniTop 12 (x4) and Titan 39 (x2) build
We'll probably end up using staples, but thanks for the tip.BoostFab wrote:if you use the spray adhesive, spray on both surfaces..the wood and the foam, and let it sit for a bit before applying the foam onto the wood.